JLab Audio FIT SPORT 3 User Manual

FIT SPORT 3 WIRELESS EARBUDS
FIRST TIME SETUP: BLUETOOTH PAIRING
Select “JLab BT” in your
device settings to connect.
Light will slow blink blue
when Bluetooth is paired.
Bluetooth
JLab BT
Settings
32
Turn on the Bluetooth
in your device settings.
Bluetooth
Settings
1
RECURRING USE
Once JLab Fit Sport 3 has initially paired to your device, the earbuds will auto-connect to your Bluetooth device when powered back ON.
(Follow BUTTON FUNCTIONS instructions)
Press and hold button
for 10 seconds.
Release.
Light will flash red
and blue to indicate
pairing mode.
C
U
S
T
O
M
E
R
S
U
P
P
O
R
T
U
.
S
.
B
A
S
E
D
We love that you are rocking JLab Audio!
We take pride in our products and fully stand behind them.
YOUR WARRANTY
All warranty claims are subject to JLab Audio
authorization and at our sole discretion. Retain your
proof of purchase to ensure warranty coverage.
CONTACT US
Reach out to us at support@jlabaudio.com
or visit jlabaudio.com/contact
L
I
M
I
T
E
D
T
W
O
Y
E
A
R
REGISTER TODAY
jlabaudio.com/register
Product updates | How-to tips
FAQs & more

JLab Audio FIT SPORT 3 Specifications

General

Type	In-ear
Wireless	Yes
Bluetooth	Yes
Charging Time	2 hours
Water Resistance	IP66
Driver Size	6 mm
Frequency Response	20 Hz - 20 kHz
Impedance	16 Ohms
Bluetooth Version	5.0
Ear Tip Sizes	Small, Medium, Large
Microphone	Yes
Colors	Black, Blue

Summary

First Time Bluetooth Pairing

Turn On Device Bluetooth

Enable Bluetooth on your mobile device before pairing the earbuds.

Initiate Earbud Pairing

Press and hold the earbud button for 10 seconds until light flashes red and blue.

Select Earbuds in Device Settings

Choose 'JLab BT' from your device's Bluetooth list to connect.

Recurring Use and Auto-Connection

Button Functions and Controls

Volume and Track Control

Single clicks for volume, long presses for track skipping. Power on/off requires holding.

Call and Voice Assistant Control

Single click to answer/hang up calls; double click to activate voice assistant.

Equalizer Modes

EQ Mode Selection

Quick press both buttons to cycle through JLab Signature, Balanced, and Bass Boost EQ settings.

Voice Prompts

Audio Feedback Messages

Earbuds provide audio cues for power status, pairing, and connection.

Charging Instructions

Connecting for Charging

Open USB door, connect to a 5V or less power source. Light turns red when charging.

Charging Completion Indicator

The indicator light turns blue when the earbuds are fully charged.

Earbud Fitting Guide

Selecting Ear Tips

Choose the correct ear tip size and optional Cush Fin for a secure and comfortable fit.

Adjustable Tip Placement

Position the earbud for optimal sound and comfort using the adjustable tip.

Wearing Around the Ear

Start from the back and rotate the earbud around the ear for secure placement.

Securing the Cable

Route the cable in front, back, and bottom for a tidy and secure fit.

Cable Clip Use

Attaching the Cable Clip

Clip the cable near the center and attach it to the front or back of your shirt.

Connection Troubleshooting

Device Does Not See JLab BT

Toggle Bluetooth off/on. If still not visible, repeat initial pairing steps.

Device Does Not Reconnect

Forget the 'JLab BT' from device settings, toggle Bluetooth, and re-pair.

Bluetooth Connectivity Troubleshooting

Connecting to Unwanted Device

Turn off Bluetooth on other devices. If needed, re-initiate pairing mode.

Important Warnings

USB Door Security

Ensure the USB door is closed and fastened to protect against sweat and water damage.

Drying Before Charging

Allow earbuds to air dry completely before charging to prevent internal damage.

Product Cautions

Liquid and Moisture Avoidance

Avoid getting moisture or liquids into the earbud tips or charging port.

Environmental Extremes

Avoid exposure to extreme heat, cold, and humidity.

Physical Handling

Avoid dropping, crushing, or excessive force on the cable.

Earwax Management

Clean earwax from tips with a cotton swab for optimal sound quality.

Discomfort and Usage

Lower volume or discontinue use if discomfort occurs. Consult physician for regular discomfort.

Care and Storage

Treat earbuds with care and store them safely when not in use.