Johnson Controls MAP User Manual

© 2016 Johnson Controls, Inc.
Part No. 24-10737-16, Rev. E
Mobile Access Portal (MAP) Gateway
MAP Gateway is a pocket-sized web server that lever-
ages the power of mobile connectivity to maximize pro-
ductivity for daily operations.
• Commission, configure and access building automa-
tion equipment using Wi-Fi-enabled devices such as
smart phones, tablets, and laptops.
• Change and configure setpoints,
parameters and schedules. View alarms and trends
through an HTML5 browser-based interface.
Use as a portable device (and carry from site to site as
needed) or permanently mount on site.
IMPORTANT: Keep your MAP Gateway in the protec-
tive shell or stationary cradle with which it shipped.
This may help protect the unit if it is dropped.
IMPORTANT: Save this guide. It contains default
user name and password information that may be
needed to reset your MAP Gateway to factory
defaults.
European Single Point of
Contact:
NA/SA Single Point of Contact:
JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY
JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA
APAC Single Point of Contact:
JOHNSON CONTROLS
C/O CONTROLS PRODUCT MANAGEMENT
NO. 22 BLOCK D NEW DISTRICT
WUXI JIANGSU PROVINCE 214142
CHINA
QUICK START GUIDE
Mobile Access
Portal Gateway
Optional - Ethernet Setup
a. In the MAP Gateway UI, navigate to
Settings > Ethernet.
b. In the Ethernet drop-down list, select On to
enable the MAP Gateway Ethernet port.
c. Click Save on the bottom of the screen.
d. Note the address in the IP Address field.
By default, the MAP Gateway is configured
to dynamically receive an IP address from
your network using DHCP. If the IP
address does not appear, refresh the
screen.
e. Enter this IP address in your browser
address bar to access the MAP Gateway
over an Ethernet network.
Refer to the Mobile Access Portal Gateway
Network and IT Guidance Technical Bulletin
(LIT-12012015) for more options.
Use the MAP Gateway
Select a device from the equipment list
and use the web pages from the MAP
Gateway to view, commission and configure
devices as needed.
IMPORTANT: The MAP Gateway must be
plugged into external power for Ethernet
use. Get approval from the site’s
IT Administrator before connecting to the
Ethernet network.
6
7

Johnson Controls MAP Specifications

General

Product Type	Gateway
Manufacturer	Johnson Controls
Model	MAP
Power Supply	24 VAC/VDC
Enclosure Rating	IP20
Communication Protocol	N2
Communication Ports	Ethernet, RS-485

Summary

Mobile Access Portal (MAP) Gateway Overview

Product Description

A pocket-sized web server leveraging mobile connectivity to maximize productivity for daily operations.

Key Functionalities

Commission, configure, access equipment, change setpoints, view alarms/trends via HTML5 browser.

Usage Scenarios

Use as a portable device or permanently mount on site for access to building automation equipment.

Handling Precautions

Keep the MAP Gateway in its protective shell or stationary cradle to prevent damage if dropped.

Document Retention

Save this guide for default user name and password information needed for factory resets.

Optional - Ethernet Setup

Ethernet Configuration Steps

Steps to enable the MAP Gateway's Ethernet port via its UI and obtain an IP address.

Additional Ethernet Guidance

Refer to the Mobile Access Portal Gateway Network and IT Guidance Technical Bulletin for more options.

Use the MAP Gateway

Device Management

Select devices from the equipment list to view, commission, and configure them via the MAP Gateway.

Getting Started

Connect MAP Gateway to Equipment

Connect the MAP Gateway to external power and then to the equipment controller via RJ-12 cable or field bus adapter.

Connect to MAP Gateway Wi-Fi

Connect your mobile device or laptop to the MAP Gateway Wi-Fi network using default SSID and passphrase.

Access MAP Gateway via Web Browser

Direct your browser to www.mapgwy.com to open the MAP Gateway browser interface.

Log in to MAP Gateway

Log in using the default Admin login credentials and accept the license agreement.

Change Passwords and Passphrase

Change the Admin password and Wi-Fi passphrase on the first login for security.