Johnson Controls Tyco PRV-1A - Limited Warranty; Ordering Procedure

TFP1581
Page 14 of 14
NATIONAL FIRE PROTECTION ASSOCIATION and NFPA are registered trademarks of National Fire Protection Association;
CLA-VAL is a trademark of Cla-Val; TEFLON is a registered trademark of DuPont
1400 Pennbrook Parkway, Lansdale, PA 19446 | Telephone +1-215-362-0700
© 2020 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.
Limited
Warranty
For warranty terms and conditions, visit
www.tyco-fire.com.
Ordering
Procedure
North America
Pressure Reducing Valve
Specify: Size (specify), 125 psi (8,6 bar)
Outlet “Set Pressure” with (G x G, or
F x F) Connection, P/N (specify):
• Valve Size
2, 3, 4, 6, or 8 in.
•
125 psi (8,6 bar) Outlet “Set
Pressure” Pressure
• Connection Type - Grooved or
Flanged
2 in. G x G
2.37 in. (60,3 mm)
Groove O.D. ..................55-001-2-020
3 in. G x G
3.50 in. (88,9 mm)
Groove O.D. ..................55-001-2-030
4 in. G x G
4.50 in. (114,3 mm)
Groove O.D. ..................55-001-2-040
6 in. G x G
6.62 in. (168,3 mm)
Groove O.D. ..................55-001-2-060
8 in. G x G*
8.62 in. ( 219,1mm )
Groove O.D ..................55-001-2-080
3 in. F x F
ANSI Flange ..................55-002-2-030
4 in. F x F
ANSI Flange ..................55-002-2-040
6 in. F x F
ANSI Flange. .................55-002-2-060
8 in. F x F*
ANSI Flange ..................55-002-2-080
* = FM only.
Pressure Relief Valve
Specify: 3/4 in. (DN20) Threaded NPT
Globe Configuration, CLA-VAL Model
55L-60 Pressure Relief Valve, P/N
55L60270
Replacement Valve Parts
Specify: (description) for use with
(specify) size Model PRV-1
A Pressure
Reducing Valve, P/N (specify, see
Figures 3 and 7)
South America, Central
America and Eastern Hemisphere
Pressure Reducing Valve
Specify: Size (specify), 125 psi (8,6
bar) Outlet “Set Pressure” with
(G x G, or F x F) Connection, for
grooved valves specify outer diame-
ter (O.D.) pipe size; for flanged valves
specify flange drilling, P/N (specify):
• Valve Size
2, 3, 4, 6, or 8 in.
•
125 psi (8,6 bar) Outlet “Set
Pressure” Pressure
• Connection Type - Grooved or
Flanged
•
For anged, identify ange drilling
specication as follows:
ANSI B16-1 (Class 125)
ISO 7005-2 (PN16)
Note: See Table A for flange drilling
dimensional specifications.
2 in. G x G
2.37 in. (60,3 mm)
Groove O.D. ..................55-001-2-020
3 in. G x G
3.50 in. (88,9 mm)
Groove O.D. ..................55-001-2-030
4 in. G x G
4.50 in. (114,3 mm)
Groove O.D. ..................55-001-2-040
6 in. G x G
6.62 in. (168,3 mm)
Groove O.D. ..................55-001-2-060
8 in. G x G*
8.62 in. (219,1mm)
Groove O.D ..................55-001-2-080
3 in. F x F
ANSI Flange ..................55-002-2-030
3 in. F x F
ISO (PN16) Flange . . . . . . . . . . . . 55-004-2-030
4 in. F x F
ANSI Flange ..................55-002-2-040
4 in. F x F
ISO (PN16) Flange . . . . . . . . . . . . 55-004-2-040
6 in. F x F
ANSI Flange ..................55-002-2-060
6 in. F x F
ISO (PN16) Flange . . . . . . . . . . . . 55-004-2-060
8 in. F x F*
ANSI Flange ..................55-002-2-080
8 in. F x F*
ISO (PN16) Flange . . . . . . . . . . . . 55-004-2-080
* = FM only.
Pressure Relief Valve
Specify: 3/4 in. (DN20) Threaded NPT
Globe Configuration, CLA-VAL Model
55L-60 Pressure Relief Valve, P/N
55L60270
Replacement Valve Parts
Specify: (description) for use with
(specify) size Model PRV-1
A Pressure
Reducing Valve, P/N (specify, see
Figures 3 and 7)