How to fix difficulty starting Jonsered CS 2166 Chainsaw?
If you're having difficulty starting your Jonsered Chainsaw, try these solutions: Adjust the L screw, check if the air filter is blocked, ensure the choke is working, and inspect for a worn choke pivot or valve. Also, verify that the fuel filter and fuel line aren't blocked, and check for a seized piston ring or a blocked impulse channel.
What to do if Jonsered CS 2166 does not accelerate?
If your Jonsered Chainsaw does not accelerate, you can try the following: Adjust the L and H screws. Check for a blocked air filter, fuel tank vent, or fuel filter. Also, inspect for a blocked fuel line or a loose/damaged fuel hose. Other potential issues include a blocked impulse channel, a loose cover on the carburettor pump side, a faulty pump diaphragm, a leaking air intake hose, loose carburettor mounting bolts, a needle valve set too low, an incorrectly assembled metering system, a sticking needle valve assembly, faulty diffuser jets, or a blocked silencer.
Why Jonsered Chainsaw carburettor leaking fuel?
If the carburettor of your Jonsered Chainsaw is leaking fuel, it could be due to a loose or faulty fuel pipe, a hole in the diaphragm, a worn needle valve, a needle valve assembly sticking, the needle valve being set too high, a leak in the metering system (air or fuel), or a loose cover on the carburettor pump side.
What to do if Jonsered CS 2166 will not run at full throttle?
If your Jonsered Chainsaw will not run at full throttle, consider these possible solutions: Adjust the H screw, check for blocked air filter, fuel tank vent, or fuel filter. Also, inspect for blocked fuel line, loose or damaged fuel hose, leaking or blocked impulse channel, loose cover on carburettor pump side, or faulty pump diaphragm. Other possible causes include leaking air intake hose, loose carburettor mounting bolts, needle valve set too low, damaged or incorrectly assembled metering system, leaking control diaphragm/cover plate, sticking needle valve assembly, or blocked silencer.
How to fix Jonsered CS 2166 idling uneven?
To fix an uneven idling issue in your Jonsered Chainsaw, try the following: Check for a blocked fuel filter or fuel line, a leaking air intake hose, or loose carburettor mounting bolts. Also, inspect for a worn throttle valve pivot, a loose throttle valve screw, or a worn throttle valve. Other potential causes include a sticking needle valve assembly, a leak in the metering system, a worn metering system centre knob, a hole in the diaphragm, a leaking control diaphragm/cover plate, or a crankcase leak.
Why Jonsered CS 2166 engine stalls when throttle released?
If the engine of your Jonsered Chainsaw stalls when the throttle is released, try these solutions: Adjust the L and H screws. A faulty pump diaphragm, a needle valve set too high or sticking, or faulty diffuser jets could also be the cause.
What to do if Jonsered CS 2166 will not idle?
If your Jonsered Chainsaw will not idle, you can try the following: Adjust the L screw. Check for a leaking air intake hose or loose carburettor mounting bolts. Also, inspect for a loose or faulty fuel hose, a blocked fuel filter or fuel line, or a blocked fuel tank vent. Other potential issues include a stiff throttle valve pivot, a sticking throttle pushrod, a defective throttle return spring, a bent throttle stop, or a faulty diffuser jet.
Why Jonsered CS 2166 flooding when engine not running?
If your Jonsered Chainsaw is flooding when the engine is not running, it might be due to a worn needle valve, a needle valve set too high, or a needle valve assembly sticking.
How to resolve low power in Jonsered CS 2166?
To resolve low power in your Jonsered Chainsaw, you might want to: Adjust the H screw, check for a blocked fuel tank vent or fuel filter. Also, inspect for a leaking or blocked impulse channel, a loose cover on the carburettor pump side, or a faulty pump diaphragm. Other possibilities include a blocked air filter, a sticking needle valve assembly, a leak in the metering system, an incorrectly assembled metering system, a loose diaphragm rivet, a hole in the diaphragm, or a leaking control diaphragm/cover plate.
Why Jonsered CS 2166 Chainsaw idling too rich?
If your Jonsered Chainsaw is idling too rich, try these solutions: Adjust the L screw, check for a worn needle valve, a needle valve set too high, a worn needle valve lever, a leaking control diaphragm/cover plate, or a needle valve assembly sticking.
General| Power Output | 3.2 kW |
|---|---|
| Chain Pitch | 0.325 inches |
| Fuel Tank Volume | 0.5 L |
| Oil Tank Volume | 0.25 L |
| Engine displacement | 64.1 cm³ |
| Chain Gauge | 1.5 mm |
| Weight (without cutting equipment) | 5.8 kg |
To Next Page
