JOYEE ZJ9610 - Height of the Feed Wheel on the 9620

9.03.11 9625
Height of the feed wheel on the 9625
 

 ，（ ）。
 ， 。
1.
2.
4 0.8 mm
4 0.3 mm
Requirement
4
0.8 mm
4
0.3 mm
1. when pressure is applied to the feed wheel , it should protrude from
the needle plate by tooth height (approx. ).
2. when no pressure is applied to the feed wheel , it should have a ver-
tical play of approx. .
● 。
●   。
●   ，  
。
●
 。
●    。
●
●
●
●
●
1 2
1 3 3 4
1
2 5 2
1 2
3 Requirement 1
3 4
1
5 Requiremnet 2 2
Swing out the roller presser.
Loosen screws and .
Adjust drive wheel according to , taking care to see that
the teeth of drive wheel and feed wheel lock into each other properly.
Tighten screws .
Adjust guide according to and tighten screws .
9-15
 Adjustment
9.05.04
Bevel gear play
( 9625 9620 )
(on the 9625 and 9620)
  
9-48
 Adjustment

，  。
，  。
1.
2.
6 7
6 8
Requirement
6 7
6 8
1. when sewing forwards, there must be a slight play between bevel gears
and .
2. When sewing backwards, there must be a slight play between bevel
gears and .
/
Disconnect air supply of the air filter/ lubricator.
Move unit by hand as far as possible to the right.
Adjust bracket (screws ) according to .
Move unit by hand as far as possible to the left.
Adjust screw (nut ) according to
●
 。
●  。
●
  （ ）。
● 1。
●
  （ ）。
●
●
●
●
● .
1
1 2 3
2 2 5
1
2 3 Requirement 1
1
4 5 Requirement 2
9.03.12 9620
Height of the feed wheel on the 9620
 
9.03.12 9620
Height of the feed wheel on the 9620
 

 ，（ ）。
 ， 。
1.
2.
40.8 mm
40.3 mm

 ，（ ）。
 ， 。
1.
2.
4 0.8 mm
4 0.3 mm
Requirement
4
0.8 mm
4
0.3 mm
1. when pressure is applied to the feed wheel , it should protrude
from the needle plate by tooth height (approx. ).
2. when no pressure is applied to the feed wheel , it should have
a vertical play of approx. .
Requirement
4
0.8 mm
4
0.3 mm
1. when pressure is applied to the feed wheel , it should protrude
from the needle plate by tooth height (approx. ).
2. when no pressure is applied to the feed wheel , it should have
a vertical play of approx. .
● 。
●   （）。
●   ，  
。
●  。
●    。
●
●
●
●
●
12
1334
1
252
12
3 Requirement 1
34
1
5 Requirement 2 2
Swing out the roller presser
Loosen screws and (two screws each).
Adjust drive wheel according to , taking care to see that
the teeth of drive wheel and feed wheel lock into each other properly.
Tighten screws .
Adjust guide according to and tighten screws .
● 。
●
  （）。
●   ，  
。
●
 。
●    。
●
●
●
●
●
1 2
1 3 3 4
1
2 5 2
1 2
3 Requirement 1
3 4
1
5 Requirement 2 2
Swing out the roller presser
Loosen screws and (two screws each).
Adjust drive wheel according to , taking care to see that
the teeth of drive wheel and feed wheel lock into each other properly.
Tighten screws .
Adjust guide according to and tighten screws .
9-16
 Adjustment
 Adjustment
9.05.03
Bevel gears for feed wheel drive
( 9625 9620 )
(on the 9625 and 9620)
  
 Adjustment
9-47

 。
   。
1.
2.
3
3 5 14 mm
●  （ ）。
●   （ ）。
●   （ ）。
●
●
●
1 2
1 3 4
2 5 6
1 2
3 4 Requirement 1
5 6 Requirement 2
Remove control unit (screws ).
Adjust bevel gear (screw ) according to .
Adjust beve gear (screw ) according to .
Requirement
3
14 mm 3
5
1. bevel gear must fit well on the left side.
2. there must be a distance of between bevel gear and bever
gear .

 19 0* 260 6  13
Zj 96 10、9620、9625、9630
08 .0 4.2