JRC JMR-9230-S3 - Page 47

4.3 Setti
ng Up a Language
[ALL]
..
........................................................................... 4-9
4.4 Subsystem Installation
[ALL]
........................................................................... 4-10
4.5 Setting Up CCRP (Consistent Common Reference Point)
[A
LL]
................. 4-15
4.6 Setting Up a Serial Port
[ALL]
..
........................................................................ 4-17
4.7 Setting Contacts (Contact Input/Output)
[ALL]
..
......................................... 4-28
4.8 CAM Configuration and Setting
[AL
L]
..
.......................................................... 4-35
4.9 Setting A/D (Analog/Digital)
[
ALL]
..
................................................................. 4-45
4.10 Setting Data Output
[RADA
R][ECDIS]
..
................................................................. 4-51
4.11 Network Setting
[ALL]
..
..................................................................................... 4-56
4.12 Redundancy Setting
[AL
L]
..
............................................................................. 4-62
4.13 Setting Ship’s Parameters
[
ALL]
..
...................................................................... 4-64
4.14 Setting Alert
[
ALL]
..
........................................................................................... 4-65
4.15 Operation Setting at AC Power Failure (Insufficient AC power supply)
[ALL]
4-67
4.16 Setting Interswitch
[RA
DAR]
..
............................................................................ 4-69
4.17 Setting VDR
[RA
DAR][ECDIS]
..
.............................................................................. 4-71
4.18 Setting Autosail (Automatic Sailing System)
[ECDIS]
..
.................................. 4-73
4.19 Setting AIS
[R
ADAR][ECDIS]
..
................................................................................ 4-80
4.20 Setting Display Size
[
ALL]
..
.............................................................................. 4-81
4.21 Tune Adjustment
[RA
DAR]
..
............................................................................... 4-83
4.22 Bearing Adjustment
[RADAR][ECDIS]
..
................................................................. 4-84
4.23 Range Adjustment
[RA
DAR][ECDIS]
..
................................................................... 4-85
4.24 Master/Slave Radar Operation Mode
[RA
DAR][ECDIS]
..
..................................... 4-86
4.25 Setting an Antenna Height
[R
ADAR][ECDIS]
.......................................................... 4-87
4.26 Tune Peak Adjustment
[R
ADAR]
....................................................................... 4-88
4.27 Setting a Tune Indicator (tuning indicator level)
[R
ADAR]
..
........................... 4-89
4.28 Setting Output BP (Radar Antenna Bearing Pulse Output)
[RA
DAR]
..
......... 4-90
4
.29
Pe
rformance Monitor Adjustment
[RADA
R]
..
.......................................................... 4-91
4.30 Setting Sector Blank (RADAR Screen Only)
[R
ADAR]
..
.................................. 4-99
4.31 Setting TNI Blank
[RADAR]
..
............................................................................ 4-100
4.32 Setting Input BP Count
[R
ADAR][ECDIS]
..
......................................................... 4-101
4.33 Setting Output BP Count
[R
ADAR]
..
............................................................... 4-102
4.34 Echo Noise Level Adjustment
[RA
DAR][ECDIS]
..
.............................................. 4-103
4
.35
T
T (Target Tracking) Function Adjustment (RADAR Screen Only)
[RADAR]
..
........ 4-104
4.36 Adjusting MBS
[RA
DAR][ECDIS]
......................................................................... 4-110
4.37 Setting Cable Attenuation
[A
LL]
..................................................................... 4-111