What does error code 4918 mean on a Jungheinrich ETX 513 Forklifts?
The error code 4918 on your Jungheinrich Forklifts indicates that the deadman button was pressed during the power-up test. To resolve this, do not press the deadman button, and switch the truck off and on again.
What does error code 4917 mean on a Jungheinrich ETX 513?
The error code 4917 on your Jungheinrich Forklifts indicates that a button / function pre-select button (switch guidance on/ off, Aux. Lift raise/ lower) was pressed during the power-up test. To fix this, do not press the button / function pre- select button (switch guidance on/off, Aux. Lift raise/lower), switch the truck off and on again.
What does error code 4916 mean on a Jungheinrich ETX 513 Forklifts?
The error code 4916 on your Jungheinrich Forklifts indicates that during the power-up test a "Functions" button under the driver's display and /or a key on the numerical keypad has been pressed. To solve this, do not press the "Functions" button, switch the truck off and on again.
What does error code 1901 mean on a Jungheinrich Forklifts?
The error code 1901 on your Jungheinrich Forklifts indicates that the accelerator pedal was pressed during the power up test. To solve this, do not press the accelerator pedal, switch the truck off and on again.
What does error code 2902 mean on a Jungheinrich Forklifts?
The error code 2902 on your Jungheinrich Forklifts indicates that the "Hydraulics" control lever was applied during the power-up test. To fix this, do not apply the "Hydraulics" control lever; switch the truck off and on again.
What to do if my Jungheinrich ETX 513 truck cannot lift a load?
If your Jungheinrich Forklifts truck cannot lift a load, it could be due to several reasons: * The truck might not be operational. Refer to the troubleshooting steps for a truck that does not start. * The battery charge might be too low, activating the lift cutout. Check the battery charge and charge the battery if necessary. * The lift cutout might be activated. Press the button under the "lift cutout override" symbol. * There might be insufficient hydraulic oil. Check the hydraulic oil level and top it up if needed. * A fuse might be faulty. Check the fuses and replace them if necessary.
Why my Jungheinrich ETX 513 truck cannot be steered?
If the Jungheinrich Forklifts truck cannot be steered, it may be due to the following reasons: * The truck is not operational. You should carry out all remedial measures listed under “Truck does not start.” * Automatic guidance is switched on. You should press the “Switch automatic guidance on/off” button and switch off "Travelling in narrow aisle."
Why is rapid travel disabled on my Jungheinrich Forklifts?
Rapid travel may be disabled on your Jungheinrich Forklifts truck for the following reasons: * The main lift is raised above 0.5 m. Lower the Main lift below 0.5 m. * WG search mode is activated. Align the truck or turn off WG mode. * No reference run has been performed. * The load is in the scanning range of the personal protection system laser scanner. Raise the Main Lift until the "protection field infringement" symbol is no longer displayed.
What does error code 9963 mean on a Jungheinrich Forklifts and how to fix it?
The error code 9963 on your Jungheinrich Forklifts indicates that the front screen of the personal protection system (PPS) laser scanner is dirty. To resolve this, clean it.
What does error code 3752 mean on a Jungheinrich ETX 513 Forklifts?
The error code 3752 on your Jungheinrich Forklifts indicates that the truck has abandoned the guide wire. To fix this, restore wire guidance.
General| Brand | Jungheinrich |
|---|---|
| Model | ETX 513 |
| Category | Forklifts |
| Language | English |
To Next Page