What does error 338 mean on Jungheinrich Forklifts?
Error 338 on your Jungheinrich Forklifts indicates that the foot switch was pressed during the power-up test. To resolve this, do not press the foot switch, then switch the truck off and on again.
What does error 330 mean on Jungheinrich EKS 314?
Error 330 on your Jungheinrich Forklifts means the drive control button was pressed during the power-up test. Avoid pressing the drive control button, then switch the truck off and on again.
What does error 331 mean on Jungheinrich EKS 314?
Error 331 on your Jungheinrich Forklifts indicates that the hydraulic control button was pressed during the power-up test. To fix this, do not press the hydraulic control button; instead, switch the truck off and then on again.
What does error 339 mean on Jungheinrich EKS 314 Forklifts?
Error 339 on your Jungheinrich Forklifts indicates that a membrane switch under the display unit was pressed during the power-up test. To resolve this, do not press the membrane switch; switch the truck off and then on again.
What does error 144 mean on Jungheinrich Forklifts?
Error 144 on Jungheinrich Forklifts means the truck has quit guidance wire. Restore wire guidance.
How to troubleshoot a Jungheinrich Forklifts truck that does not drive?
If your Jungheinrich Forklifts truck isn't moving, several factors could be at play. First, make sure the battery plug is securely connected. Check that the safety gates are fully closed and the EMERGENCY DISCONNECT switch is not engaged. Also, ensure the key switch is in the “I” position and the battery has sufficient charge. Don't forget to press the foot switch. Finally, inspect the fuses and ensure that the travel cutout is not activated, and that the chains are not slack. If the travel cutout was activated via the aisle end safety device, set the foot switch or travel button to neutral and press it again.
What to do if my Jungheinrich EKS 314 truck cannot lift a load?
If your Jungheinrich Forklifts truck won't lift loads, start by ensuring the truck is operational by checking all items listed under “Truck does not start.” Also, verify that the battery isn't too low (lift cutout). Finally, check the fuses and ensure that the chains are not slack.
Why is rapid travel disabled on my Jungheinrich EKS 314?
If the rapid travel function is disabled on your Jungheinrich Forklifts truck, it might be because the main lift is raised beyond 0.5 m/ 0.5 yard (1.6 ft). Lower the main lift below this height. Also, check if WG search mode is activated; if so, align the truck or turn off WG mode. Finally, ensure a test run has been performed by lifting and lowering.
What causes a Jungheinrich Forklifts truck to not steer?
If your Jungheinrich Forklifts truck isn't steering, first ensure the truck is operational by checking all items listed under “Truck does not start.” Also, verify that the narrow aisle mode switch is off.
General| Load Capacity | 1400 kg |
|---|---|
| Lift Height | up to 10700 mm |
| Weight | 3760 kg |
| Battery Capacity | 620 Ah |
| Travel Speed | 11 km/h |
| Drive | Electric |
| Battery Voltage | 48 V |
Explains DANGER, WARNING, CAUTION, IMPORTANT, NOTICE symbols and their meanings.
Emphasizes the importance of trained and certified personnel for industrial truck operation.
Lists essential safety practices like training, awareness, and hazard avoidance.
Outlines limitations on manufacturer responsibility and invalidation of instructions.
Details user responsibilities for safe operation, maintenance, and adherence to regulations.
Guidelines for attaching accessories and making modifications to the truck.
Importance and role of identification plates and warning labels on the truck.
Lists specific prohibited actions and essential safety rules for truck operation.
Details the intended application and required floor surface conditions for the EKS 314.
Details the main components and their functions, including safety mechanisms and systems.
Covers performance data, dimensions, mast versions, US standards, EMC, and application conditions.
Explains identification points, warning labels, data plates, and capacity information.
Details the operating and display equipment on the truck's control panel.
Explains various symbols and controls found on the truck's display unit.
Step-by-step procedures for starting up and preparing the truck for operation.
Guides on how to operate the truck's travel, steering, and braking systems.
Procedures for lifting and lowering loads inside and outside rack lanes.
Steps for collecting, transporting, and depositing loads, including fork adjustment.
Guidelines for securely parking the truck when unattended.
Covers training, damage, load issues, and work environment safety.
Explains the emergency stop device and driver's cab emergency lowering procedure.
Covers operator responsibilities, pre-shift checks, and general operating practices.
Advice on preventing tipovers and procedures for securing the truck.
Safety rules for lifting personnel if the truck is equipped for it.
Explains overrides for slack chain safety, travel cutout, and lift limit devices.
Procedures for emergency operations related to wire guidance systems.
Procedures for recovering the truck and managing battery operations.
Covers safety rules for handling lead-acid batteries, including fire protection and disposal.
Information on available battery types and their compatibility with the truck.
Instructions for charging the truck battery.
Step-by-step guide for battery removal and installation.
How to check battery condition, acid level, density, and discharge indicator.
Covers operational safety, environmental protection, and rules for maintenance personnel.
Details lifting, cleaning, electric system work, and component checks.
Covers hydraulic hoses, maintenance rules, and system checks.
Procedures for inspecting and repairing forks used on industrial trucks.
Importance of regular servicing and inspection intervals, including checklists.
Detailed checklist for chassis, drive, wheels, steering, and brakes maintenance.
Continuation of checklist for hydraulic, electrical systems, motors, and batteries.
Checklist items for lift mechanism, safety devices, lubrication, and measurements.
Diagram illustrating lubrication points on the truck.
Table of lubricants with order numbers, quantities, and usage.
General information and safety rules for performing maintenance and repairs.
Procedures for securing the mast and servicing lift chains.
How to inspect lift chains for wear and damage.
Procedures for draining, adding, and checking hydraulic oil, including fluid types.
Information on the replacement schedule for hydraulic hoses.
How to check and replace electrical fuses with a rating table.
Steps to recommission the truck after cleaning or maintenance work.
Procedures for decommissioning the truck for extended periods.
Measures during decommissioning and procedures to recommission the truck.
Requirements for regular safety inspections and final disposal procedures.
Guides users on diagnosing and fixing common truck issues like no drive or steering problems.
Guides users on diagnosing and resolving specific error codes displayed on the truck.
Details methods for transporting the truck, including lifting by crane and securing.
Procedures for loading the truck by crane with the mast folded or disassembled.
Identification of crane points and procedures for lifting the battery by crane.
How to securely fasten the truck for transport.
General safety measures for transporting the truck.
Safety measures when transporting the mast.
Procedures for safely transporting the truck with the mast assembled.
Steps for moving the truck without a battery and initial commissioning after transport.
Procedure for moving the truck without a battery.
Procedures for installing/removing or erecting/folding the mast.
Essential checks for tilt safety device, safety restraint belt, and overall safety devices.
To Next Page