Jungheinrich EKS 410 - User Manual

Questions and Answers

A
amybrooksAug 16, 2025
What to do if my Jungheinrich EKS 410 truck does not start?
- C
  Corey ScottAug 16, 2025
  If your Jungheinrich Forklifts truck isn't starting, here are a few things to check: * Ensure the battery plug is connected. * Close the safety gates. * Unlatch the EMERGENCY DISCONNECT switch. * Set the key switch to “I.” * Check the battery charge and charge if necessary. A low battery can prevent the truck from starting. * Press the foot switch. * Inspect the fuses. * Press the travel cutout override switch. * Set the foot switch or travel button to neutral and press it again.
R
robertburkeAug 19, 2025
What does Error 331 mean on Jungheinrich EKS 410 Forklifts?
- J
  Johnny HollandAug 19, 2025
  If you see Error 331 on your Jungheinrich Forklifts truck, it indicates that the hydraulic control button was pressed during the power-up test. To fix this, avoid pressing the hydraulic control button, then switch the truck off and on again.
J
Jessica RobinsonAug 22, 2025
How to clear Error 332 on Jungheinrich Forklifts?
- M
  Michael BrownAug 22, 2025
  If your Jungheinrich Forklifts truck displays Error 332, it means a key below the display unit was pressed during the power-up test. To correct this, do not press any keys, then switch the truck off and on again.
J
Jennifer KingAug 26, 2025
What does Error 144 mean on Jungheinrich EKS 410?
- J
  Jonathan WilliamsAug 26, 2025
  If you're getting Error 144 on your Jungheinrich Forklifts truck, it means the truck has quit guidance wire. You need to restore wire guidance to resolve this issue.
K
Kathleen GibsonAug 28, 2025
Why my Jungheinrich EKS 410 Forklifts load cannot be lifted?
- C
  chughesAug 28, 2025
  If the load cannot be lifted on your Jungheinrich Forklifts truck, consider the following: * First, make sure the truck is operational by checking all the points listed under “Truck does not start.” * Check the battery charge and charge if necessary, as a low battery can trigger a lift cutout. * Also, verify the hydraulic oil level and top up if it's insufficient.
H
hallfeliciaAug 31, 2025
How to fix rapid travel disabled on Jungheinrich Forklifts?
- W
  William SandersAug 31, 2025
  If rapid travel is disabled and your Jungheinrich Forklifts truck cannot be steered, consider these potential causes: * If the Primary raise / Aux. Lift is raised above 0.5m, lower it below 0.5m. * Try to align the truck or turn off WG mode. * Perform lifting and lowering. * Ensure the truck starts by following the steps outlined in “Truck does not start.” * Switch off the narrow aisle travel function.
M
Melissa LeeSep 3, 2025
What to do if I see Error 330 on Jungheinrich EKS 410?
- M
  Miss Brenda Arias DVMSep 3, 2025
  If you are getting Error 330 on your Jungheinrich Forklifts truck, it means the travel control button was pressed during the power-up test. To resolve this, do not press the travel control button, switch the truck off and then on again.
C
Craig BrownSep 6, 2025
What causes Error 333 on Jungheinrich Forklifts?
- J
  Joseph TorresSep 6, 2025
  If your Jungheinrich Forklifts truck shows Error 333, it indicates that a function preselect key aux. lift was pressed during the power up test. To resolve this, do not press the function preselect key aux. lift, then switch the truck off and on again.
T
turnerbrandonSep 9, 2025
How to resolve Error 334 on Jungheinrich EKS 410?
- E
  Elizabeth TorresSep 9, 2025
  If you encounter Error 334 on your Jungheinrich Forklifts truck, it means the foot switch was pressed during the power-up test. To solve this, do not press the foot switch, and then switch the truck off and on again.
I
Isaac JacksonSep 12, 2025
What to do if I see Error 344 on Jungheinrich EKS 410?
- C
  Chad ReeseSep 12, 2025
  If you're seeing Error 344 on your Jungheinrich Forklifts truck, it's due to the personal safety system. The PSA scanner is contaminated, so you should clean it.