3
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require
information regarding installation kits, consult your JVC car audio dealer or a company supplying
kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
*
3
When you stand the unit, be careful not to damage the fuse on the rear.
*
3
৹ʹጅçʮ˻ʿ࠱๑ᖢנ௰ڄۘᎳീé
Do the required electrical
connections.
නмᄔڄྐཔé
Bend the appropriate tabs to hold
the sleeve firmly in place.
Ҿᛮጅೋڄߴдçӕࢭጅೋԕ֣
Ϛᄭڷػ˖é
Removing the unit
Before removing the unit, release the rear section.
Insert the two handles, then pull them
as illustrated so that the unit can be
removed.
ݝ࿌Εçઅղػܓӕ˾ʈ
ᆥç݈ძᗌϙનղώղӕ
˾çʹጅᎲ˃é
When using the optional stay /
ࠝΈᆊނ
Screw (option)
ᒘീ·ڄ
Stay (option)
ᆉށ·ڄ
Fire wall
Վػ
Dashboard
ᄭڷػ
Install the unit at an angle of less than 30˚.
અʹጅϯ༫Ϛ˲ؠ
30˚ڄԴܾé
When installing the unit without using the sleeve /
ࠝˀՠΈࢮጆೌϰ༬͵ጆ
In a Toyota car for example, first remove the car radio and install the unit in its place.
ᕙΉ(TOYOTA) ԆԾբ ࡛ζ֊ԆԾЂࡖጅç݈અʹጅ༫ʈմڏڄтé
Bracket *
4
Ёࣙ *
4
Bracket *
4
Ёࣙ *
4
*
4
Not supplied for this unit.
*
4
ʿᎲʹጅಏաé
Flat type screws (M5 × 8 mm) *
4
Ꮓᒘീ (M5 × 8 mm) *
4
Pocket
ڏೋ
Flat type screws (M5 × 8 mm)
*
4
Ꮓᒘീ (M5 × 8 mm) *
4
Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If
longer screws are used, they could damage the unit.
ٍิ ! ӕʹጅϯ༫ϚЁࣙʕç՟·8 mmۂڄᒘീéϨ՟·ཫۂڄᒘീç๑ᖢʹጅé
։͵ጆ
Ϛ؛ֈʹጅۮçᏻઅʹጅ݈௰ڄ֣׆֜௰˜ᖑළé
ϰ༬༬éׇ֤ϛᄮڸؼ˗
ʓࡒڄ࿌༱ڷΕʄյܓڄϯ༫ദҺéϨسЉᖅçᄔ࠱Љᘕࢭ˔άڄཊçቁώJVC
ԆԾࡖᛏ˜ኀࢭ˔άաᏻ˙༿é
• Ϩسʿᇧ׆Ϩщᇧϙϯ༫ʹጅçᏻቁϐڄӑிʆ࢜գϯ༫é
Instal1-3_DV6206_005A_1.indd 3Instal1-3_DV6206_005A_1.indd 3 2/23/06 2:33:53 PM2/23/06 2:33:53 PM
To Next Page
Loading...
Need help?
General
