JVC KD-X130

ENGLISH
11
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
SUB.W LEVEL
*
4
SPK-OUT
*
5
00 to +06 ( +03 ):Adjusts the output level of the
subwoofer connected via speaker lead. (
 17 )
PRE-OUT
*
6
–08 to +08 ( 00 ):Adjusts the output level of the
subwoofer connected to the lineout terminals (REAR/SW)
through an external amplifier. (
 17 )
SUB.W
*
6
ON / OFF : Turns on or off the subwoofer output.
SUB.W  LPF
*
4
THROUGH :All signals are sent to the subwoofer. ; LOW  55HZ /
MID  85HZ / HIGH120HZ :Audio signals with frequencies lower than
55Hz/ 85Hz/ 120Hz are sent to the subwoofer.
SUB.WPHASE
*
4
REVERSE (180°)/ NORMAL (0°):Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than [
THROUGH ] is selected for
[
SUB.W  LPF ].)
FADER R06 — F06 ( 00 ):Adjusts the front and rear speaker output balance.
BALANCE
*
7
L06 — R06 ( 00 ):Adjusts the left and right speaker output balance.
VOL ADJUST –15 — +06 ( 00 ):Preset the initial volume level of each source
(compared to the FM volume level). Before adjustment, select the source
you want to adjust. (“VOLADJFIX” appears if FM is selected.)
AMP GAIN LOW  POWER :Limits the maximum volume level to 25. (Select if the
maximum power of each speaker is less than 50W to prevent damaging
the speakers.);
HIGHPOWER :The maximum volume level is 35.
D.T.EXP
(Digital Track
Expander)
ON :Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in
audio data compression.;
OFF :Cancels.
TEL  MUTING
*
8
ON :Mutes the sounds while using the cellular phone (not connected
through KS-BTA100).;
OFF :Cancels.
SPK/PRE  OUT Depending on the speaker connection method, select the appropriate
setting to get the desired output. (
 Speaker output settings )
AUDIO SETTINGS
*
4
Displayed only when [ SUB.W ] is set to [ ON ].
*
5
Displayed only when [ SPK/PRE  OUT ] is set to [ SUB.W/SUB.W ].
*
6
Displayed only when [ SPK/PRE  OUT ] is set to [ REAR/SUB.W ] or [ SUB.W/SUB.W ].
*
7
This adjustment will not affect the subwoofer output.
*
8
Does not work if [ BT  ADAPTER ] is selected for [ AUX ] in [ SRC  SELECT ]. (  4 )
Speaker output settings
Select the output setting for the speakers [ SPK/PRE OUT], base on the
speaker connection method.
Connection via lineout terminals
For connections through an external amplifier. (  17 )
Setting on
[ SPK/PRE OUT]
Audio signal through lineout terminal
REAR/SW
REAR/REAR Rear speakers output
REAR/SUB.W Subwoofer output
SUB.W/SUB.W Subwoofer output
Connection via speaker leads
For connections without using an external amplifier. However, with this
settings you can also enjoy the subwoofer output. (
 17 )
Setting on
[ SPK/PRE OUT]
Audio signal through rear speaker lead
L (left) R (right)
REAR/REAR Rear speakers output Rear speakers output
REAR/SUB.W Rear speakers output Rear speakers output
SUB.W/SUB.W Subwoofer output (Mute)
If [ SUB.W/SUB.W ] is selected:
– [
HIGH120HZ ] is selected in [ SUB.W  LPF ] and [ THROUGH ] is not available.
– [
R01 ] is selected in [ FADER ] and selectable range is [ R06 ]to [ 00 ].
JS_JVC_KD_X230_X130_M_EN_Pre.indd 11JS_JVC_KD_X230_X130_M_EN_Pre.indd 11 24/8/2015 10:39:44 AM24/8/2015 10:39:44 AM