1
2
4
Connections
Basic and Common Operations
Supplied Accessories
After unpacking, check to be sure that you have all the
following items.
• Remote control, RM-SUXLP6R (× 1)
• Lithium coin battery CR2025 (× 1)
– The battery has been installed in the remote control
when shipped from the factory.
• FM antenna (× 1)
• Protection sheet (× 1)
If anything is missing, consult your dealer immediately.
Prepare the Remote Control
When you use the remote control for the first time, pull out
the insulation sheet.
To Replace the Battery in the Remote Control
NOTES:
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• To prevent the battery from overheating, cracking, or starting
a fire:
– Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal,
state, and local regulations.
Basic Disc/USB Mass Storage Class Device Operations
To Press Indication/Result
Play back the disc
• Current track number and elapsed playing
time appear.
• During playback, press again to pause.
Play back the
USB mass storage
class device
Stop playback • While playback is stopped, total track number
and total playing time (for MP3/WMA files,
group number and track number) appear.
Select a track
Select the next tracks.
To go back to the beginning of the current or
previous tracks.
Select a group
(MP3/WMA only)
Select the previous groups.
Forward search/
Reverse search
Press and hold to fast-forward the track during
playback.
To stop searching, release the button.
Press and hold to fast-forward the track during
playback.
To stop searching, press 6.
Press and hold to fast-reverse the track during
playback.
To stop searching, release the button.
Press and hold to fast-reverse the track during
playback.
To stop searching, press 6.
Change display
information
Press repeatedly.
NOTES:
• If no disc is inserted or no USB mass storage class device is connected, “NO DISC” or
“NO USB” appears on the main display.
• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device,
“NO PLAY” or “NO DATA” appears on the main display.
Getting Started
Playing Back a Disc/USB Mass Storage Class Device
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files
in ISO 9660 format.
– USB mass storage class device containing MP3/WMA files.
• When playing back an MP3 or WMA track, MP3 or WMA indicator lights up.
Loading a Disc (on the System only)
1
Press to open the disc tray.
2
• When using an 8 cm (3 3/16 inch) disc, place it
on the inner circle of the disc tray.
3
Press to close the disc tray.
Connecting a USB Mass Storage Class Device
You can connect a USB mass storage class device such as a USB flash memory
device, MP3 player, multimedia card reader, etc. to the System.
NOTES:
• When connecting with a USB cable, use the USB 2.0 cable whose length is less than
1 m.
• USB mass storage class device is charged through the USB MEMORY terminal when
the System is turned on. (Some USB mass storage class device may be charged
through the USB terminal only when “USB” is selected as the source.)
• You cannot connect a computer to the USB MEMORY terminal of the System.
• Do not disconnect the USB mass storage class device when the System is turned on. It
may cause malfunction of both this System and the device.
• Noise and static electricity may stop the USB mass storage class device sound. In this
case, disconnect and connect the USB mass storage class device again after turning
off the System.
Prohibiting Disc Ejection (on the System only)
You can lock the disc tray so that no one can eject the loaded disc.
1
While no USB device is connected, select “USB” as the source.
2
Press briefly.
3
Press and hold for more than 2 seconds.
To cancel the prohibition, repeat the same procedure.
3
Playing Repeatedly—Repeat Play
1
Press repeatedly to specify the repeat mode as follows:
: Repeats the current (or specified) track.
: Repeats all tracks in the current group
(MP3/WMA only).
ALL: Repeats all tracks.
No indicator (Off): Normal playback
2
or
Programming the Playing Order—Program Play
1
During stops, press so that the PRGM (program) indicator
lights up.
2
or
Select a track number.
3
Press to program the selected track.
4
Repeat steps 2 and 3 to program other tracks you want.
• If you try to program a 33rd track, “PRG FULL” will appear.
5
or
The tracks are played back in the programmed order.
Operations for Program Play (while program stop mode)
• To check the programmed contents, press SET repeatedly.
• To add tracks, after “- - -” appears on the display by pressing SET repeatedly,
repeat steps 2 and 3 above.
• To erase or exit the program, press 7.
– The stored program is not kept.
Playing at Random—Random Play
1
Press so that the RND (random) indicator lights up and playback
starts in random order.
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track, press 4.
• To exit from random play, press RANDOM so that the RND (random) indicator
disappears during playback.
Thank you for purchasing a JVC product.
To
Press
Indication/Result
System Remote
Turn on or off
(standby) the power
The STANDBY lamp on the System turns off/on.
Select a source
• See “Playing Back a Disc/USB Mass Storage Class Device” on page 4.
• See “Listening to an iPod/Viewing Images on the iPod” on page 5.
Press repeatedly to select “TUNER FM” or “AUDIO IN.”
• For “TUNER FM,” see “Listening to FM Broadcasts” on page 5.
• For “AUDIO IN,” see “Listening to Other Equipment” on page 5.
Adjust the volume
Adjustable range: Level 0 (“VOL MIN”) to level 40 (“VOL MAX”).
Drop the volume in
a moment
—
To restore the volume, press again, or adjust the volume level.
Emphasize the
sound (Sound
Turbo)*
—
The S.TURBO indicator lights up.
To cancel this function, press again.
Reinforce the bass
sound (Hyper Bass
Sound)*
—
The BASS indicator lights up.
To cancel this function, press again.
Adjust the tone
(Bass/Treble)
—
Press once for adjusting the bass level; twice for treble level, then, press
VOLUME +/–.
Adjustable range: –3 to +3.
Dim the display
You can dim the display window and illumination lamp.
While the System is turned on...
Set the clock and
timer
—
For setting the clock, see “Setting the Clock and Using Timers” on page 6.
Change the display
information
—
The display information changes as follows:
FM: Frequency = Clock
CD: Current track elapsed time = Clock
MP3/WMA: Current track elapsed time = ID3 tag = Current group/track
= Clock
——
This button is not used for the System.
* Sound Turbo and Hyper Bass Sound cannot be used at the same time.
NOTE:
• DO NOT turn off (standby) the System with the volume set to an extremely high
level; otherwise, the sudden blast of sound can damage your hearing, speakers and
headphones when you turn on the System or start playback.
• Select a place which is level, dry and neither too hot nor too cold—between 5˚C and 35˚C.
To a wall outlet
Plug the AC power cord only after all connections are complete.
Rear view
Outdoor FM antenna
(not supplied)
Disconnect the supplied FM antenna,
and connect to an outdoor FM
antenna using a 75 Ω wire with coaxial
type connector.
FM antenna (supplied)
RESUME Play
Press RESUME to activate RESUME Play so that the RESUME indicator lights up.
When you stop the playback by one of the following operations, this System
stores the beginning of the stopped track on the disc or USB mass storage class
device.
– Pressing 7 once
– Changing the source
When you start playback again, playback starts from the beginning of the
stopped track.
To clear the memory, press 7 while playback is stopped, open the disc tray or
disconnect the USB mass storage class device.
• When you clear the memory and start playback, playback starts from the first
track
To deactivate RESUME Play, press RESUME again.
NOTE:
This function does not work in Program Play.
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
NOTES:
• Make sure the antenna conductors do not touch any other terminals, connecting
cords and power cord. Also, keep the antennas away from metallic parts of the
System, connecting cords, and the AC power cord. This could cause poor reception.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the speaker terminals:
red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch with the metallic
parts of the System.
Do not connect the AC power cord until all other connections have been made.
To connect the FM antenna (supplied)
Extend it so that you can obtain the best reception.
For better FM reception
To connect the speaker cords
Point at the remote sensor on the front panel.
Lithium coin battery
(product number: CR2025)
Press and hold
Insert
Release
Red
Black
From left
speaker
From right
speaker
LVT2263-002A EN_UX-LP55[J/C]1
VOLUME
DISPLAY
DIMMER
REPEAT
RANDOM
PR
OGRAM
A
UDIO IN
TUNER MODE
RESUME
MENU/CANCEL
AUT
O STBY
SLEEP
PTY
HBS
SOUBD
TURBO
B
ASS/TRE
BLE
CLOCK/
TIMER
FADE
MUTING
UP
CD
iPod
USB
TUNER
SET
DOWN
To connect the
monitor (not
supplied)
Video cord
(not supplied)
Insulation sheet
• The operations on pages 4 to 6 are explained using the remote control, unless
mentioned otherwise. However, if the System has the same or similar button
names, they can also be used for the operations.
• In this manual, “iPod” means iPod, iPod touch and iPhone device. When iPod
touch or iPhone device is especially referred to, “iPod touch” or “iPhone” is used.
Monitor
For USA-California Only
This product contains a CR Coin Cell Lithium Battery which
contains Perchlorate Material – special handling may
apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
STANDBY lamp
Stereo mini plug cord
PHONES jack
USB cable (not supplied)
USB memory
(not supplied)
Or
Using Headphones
• Be sure to turn down the volume before connecting or putting on the
headphones.
– Connecting the headphones will deactivate the speakers.
– Sound adjustments also affect the sound through the headphones.
• While playing back iPod/iPhone, no sound is heard from the headphones
connected to the System.
Front view
INSTRUCTIONS
LVT2263-002B[J]
0811KMMMDWCDT
© 2011 Victor Company of Japan, Limited
For U.S.A.
Caution: Changes or modifications not expressly approved by party responsible for compliance could
void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
Pour les Etats-Unis
Attention: Les changements ou les modifications qui ne sont pas explicitement approuvés par la partie
responsable de l’observance pourraient mettre fin au droit de l’utilisateur d’utiliser le matériel.
Remarque: Cet appareil a été testé et il s’est avéré conforme aux limites applicables à un appareil
numérique de classe B, en vertu de la Partie 15 des Règles de la FCC. Ces limites sont conçues de
manière à assurer une protection raisonnable contre les interférences nuisibles dans une installation
résidentielle.
Cet appareil produit, utilise et peut émettre une énergie de haute fréquence et, s’il n’est pas
installé et utilisé en conformité avec les instructions, il peut causer des interférences nuisibles aux
communications radio. Il n’y a, toutefois, aucune garantie que des interférences ne se produiront pas
dans une installation particulière.
Si cet appareil cause effectivement des interférences nuisibles à la réception de la radio ou de la
télévision, ce qu’on peut établir en mettant l’appareil en marche et à l’arrêt, nous encourageons
l’utilisateur à tenter de corriger l’interférence par une ou plusieurs des mesures suivantes :
– réorienter ou déplacer l’antenne de réception ;
– accroître la séparation entre l’appareil et le récepteur ;
– brancher l’appareil dans une prise ou un circuit autre que celui auquel le récepteur est branché ;
– consulter un vendeur ou un technicien radio/TV expérimenté pour obtenir de l’aide.
Warnings, Cautions and Others / Mises en
garde, précautions et indications diverses
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the products
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Le symbole de l’éclair à l’intérieur d’un triangle
équilatéral est destiné à alerter l’utilisateur sur la
présence d’une “tension dangereuse” non isolée dans
le boîtier du produit. Cette tension est suffisante pour
provoquer l’électrocution de personnes.
Le point d’exclamation à l’intérieur d’un triangle
équilatéral est destiné à alerter l’utilisateur sur la
présence d’opérations d’entretien importantes
au sujet desquelles des renseignements se
trouvent dans le manuel d’instructions.
[European Union only]
[Union européenne seulement]
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There
are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser
radiation when open. Do not stare into beam.
(For Canada) Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
4. CAUTION: Use of any controls, adjustments, or procedures
other than those specified herein may result in hazardous
radiation exposure.
5. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
IMPORTANT POUR PRODUITS LASER
1. PRODUIT LASER CLASSE 1
2.
ATTENTION: N’ouvrez pas le couvercle supérieur ni le coffret de
l’appareil. Il n’y a aucune pièce réparable par l’utilisateur à l’intérieur
de l’appareil; confiez toute réparation à un personnel qualifié.
3.
ATTENTION: (Pour les Etats-Unis) Radiation laser de classe II visibles
et/ou invisible si l’appareil est ouvert. Ne regardez pas le rayon.
(Pour le Canada) Rayonnement laser visible et/ou invisible
de classe 1M une fois ouvert. Ne pas regarder directement
avec des instruments optiques.
4.
ATTENTION: Toute utilisation des commandes, réglages ou
procédures autres que celles spécifiées dans ce document risque
d’entraîner une exposition dangereuse aux rayonnements.
5. REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE
PRÉCAUTION PLACÉE À L’INTERIEUR DE L’APPAREIL.
CAUTION
The button in any position does not disconnect the mains line.
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off).
The MAINS plug or an appliance coupler is used as the disconnect
device, the disconnect device shall remain readily operable.
• When the system is on standby, the STANDBY lamp lights red.
• When the system is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
ATTENTION
La touche
, quelle que soit sa position, ne coupe pas la
ligne principale.
Débrancher la fiche principale pour couper complètement
l’alimentation du secteur (le témoin STANDBY s’éteint).
La fiche secteur ou un coupleur est utilisé comme dispositif
de déconnexion de l’appareil, et l’appareil déconnecté doit
être prêt à être utilisé.
• Quand l’appareil est en mode d’attente, le témoin STANDBY
est allumé en rouge.
• Quand l’appareil est sous tension, le témoin STANDBY s’éteint.
L’alimentation peut être commandée à distance.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent
damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in the
areas indicated by the dimensions in the illustration.
3. Bottom: Place on the level surface. Maintain an adequate
air path for ventilation by placing on a stand with a
height of 10 cm or more.
ATTENTION: Aération correcte
Pour prévenir tout risque de décharge électrique ou
d'incendie et éviter toute détérioration, installez l'appareil
de la manière suivante:
1. Avant: Bien dégagé de tout objet.
2. Flancs/ Dessus/ Arrière: Aucun obstacle ne doit être
placé dans les zones indiquées par les dimensions dans
l’illustration.
3. Dessous: Posez l’appareil sur une surface plane et
horizontale. Veillez à ce que sa ventilation correcte puisse
se faire en le plaçant sur un support d’au moins dix
centimètres de hauter.
CAUTION:
•
Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a newspaper or
cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
Front view/Face Side view/Côté
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE
THIS APPARATUS TO RAIN OR MOISTURE.
AVERTISSEMENT:
POUR PRÉVENIR LES RISQUES D’INCENDIE OU DE CHOCS
ÉLECTRIQUES, NE PAS EXPOSER CE APPAREIL À LA PLUIE
OU À L’HUMIDITÉ.
CAUTION: Excessive sound pressure from earphones or
headphones can cause hearing loss.
ATTENTION: Une pression acoustique excessive des écouteurs
ou du casque d'écoute peut entraîner une perte auditive.
CAUTION: Battery shall not be exposed to excessive heat
such as sunshine, fire or the like.
ATTENTION
: Les piles ne doivent en aucun cas être
exposées à une chaleur excessive (lumière du solei, feu, etc.).
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
ATTENTION:
• Ne bloquez pas les orifices ou les trous de ventilation. (Si
les orifices ou les trous de ventilation sont bloqués par un
journal un tissu, etc., la chaleur peut ne pas être évacuée
correctement de l’appareil.)
• Ne placez aucune source de flamme nue, telle qu’une
bougie, sur l’appareil.
• Lors de la mise au rebut des piles, veuillez prendre en
considération les problèmes de l’environnement et suivre
strictement les règles et les lois locales sur la mise au
rebut des piles.
•
N’exposez pas cet appareil à la pluie, à l’humidité, à un
éqgouttement ou à des éclaboussures et ne placez pas
des objets remplis de liquide, tels qu’un vase, sur l’appareil.
CLASS II apparatus with double insulation, and
no protective earth provided.
Appareil de CLASSE II avec isolant double et
sans protection de mise à la terre.
For Canada/pour le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM
DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING EQUIPMENT STANDARD ENTITLED
“DIGITAL APPARATUS,” ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPLICABLES AUX
APPAREILS NUMERIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR LE MATERIEL BROUILLEUR;
“APPAREILS NUMERIQUES”, NMB-003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS.
MICRO COMPONENT SYSTEM
UX-LP55B
—Consists of CA-UXLP55B and SP-UXLP55B
UX-LP55W
—Consists of CA-UXLP55W and SP-UXLP55W
ENGLISH
To Next Page
Need help?
General
