K-Rain RPS Select - User Manual

B. Nozzle Selector
A. Nozzle Arrow (Right Start Position)
D. Arc Adjustment Slot
F. Break Up Screw
C. Keyhole
E. Arc Indicator
G. Nozzle Turret
H. Sprinkler Can
J. Top
K. Sprinkler
Assembly
I. Adjustment Key
ARC NOZZLE
40° to 135° Use #1 Nozzle
136° to 225° Use #2 Nozzle
226° to 315° Use #3 Nozzle
316° to 360° Use #4 Nozzle
TO SELECT NOZZLE:
Insert Adjustment Key (I)
into Nozzle Selector (B)
and turn to desired nozzle.
The RPS Select is designed to conserve
water by matching the ow rate to the arc.
The following settings are recommended:
NOTE: The RPS SELECT Gear Driven Sprinkler
has a xed right start and an adjustable left stop.
POSITIONING NOZZLE TURRET TO ITS “RIGHT START”
Place your ngers on the top center of the nozzle turret (G).
Rotate the turret counter-clockwise to the left stop to
complete any interrupted rotation cycle. Rotate the nozzle
turret clockwise to the right start. This is the xed side of
the arc. The nozzle turret must be held in this position for
arc adjustments. The right start does not change.
ADJUSTING THE RIGHT (FIXED) SIDE OF ARC
If the right side of the arc is not properly aligned, the
sprinkler may spray areas not intended for watering such
as driveways or adjacent properties. The right side arc can
easily be realigned.
OPTION 1: REPOSITION CAN ON THE FITTING
Turn the sprinkler can (H) left or right to the desired position.
This may require temporary removal of the soil around the
sprinkler to allow you to grip the sprinkler can.
OPTION 2: REMOVE INTERNAL RISER ASSEMBLY
AND REPOSITION
Unscrew the top (J) counter-clockwise and remove the
Sprinkler Assembly (K) from the can. Once removed with
nozzle turret (G) at its right start, reposition the sprinkler
assembly so that nozzle arrow (A) points to the desired
start position. Replace the sprinkler assembly back in the
can and screw on the top. At this point you have realigned
the right arc start, and you can adjust the left arc to your
desired setting.
ADJUSTING THE LEFT (VARIABLE) SIDE OF ARC
SETTING THE ARC
Insert Adjustment Key (I) into the arc adjustment slot (D).
While holding the nozzle turret (G) at the right start, turn the
Key (I) until the Arc Indicator (E) shows the desired radius.
RPS
®
Select Gear Driven Sprinkler Setting Instructions
NOTE: The RPS Select is factory preset with a 180° arc setting, and includes a pre-installed #2 nozzle.
NOZZLE SELECTION
SETTING THE ARC ADJUSTMENT
1
s
2
s

Summary

NOZZLE SELECTION

TO SELECT NOZZLE

Instructions for inserting the Adjustment Key into the Nozzle Selector to set the desired nozzle.

SETTING THE ARC ADJUSTMENT

POSITIONING NOZZLE TURRET TO ITS RIGHT START

Setting the fixed right start position of the sprinkler turret by rotating it clockwise.

ADJUSTING THE RIGHT (FIXED) SIDE OF ARC

Guidance on realigning the right side of the arc to prevent spraying unintended areas.

ADJUSTING THE LEFT (VARIABLE) SIDE OF ARC

Instructions for setting the adjustable left stop of the sprinkler's arc using the Adjustment Key.

SPRINKLER INSTALLATION

INSTALL AND BURY

Instructions for installing and burying the sprinkler flush with the ground, avoiding pipe dope.

INSPECTING THE FILTER

Procedure for removing the sprinkler assembly to access and clean the filter.

WINTERIZATION TIPS

Guidelines for using an air compressor for winterization, including PSI limits and gradual air introduction.

PERFORMANCE DATA

K-Rain RPS Select Specifications

General

Brand	K-Rain
Model	RPS Select
Category	Irrigation System
Language	English