Kärcher SV 7 User Manual

– 11
For further use of the steam and vacuuming function
see Chapter "Steaming operation and vacuuming oper-
ation"
Illustration
 Place the steam suction pipe in the parking holder
during interruptions of work.
If the appliance is not used for more than 15 minutes, it
automatically changes into the standby mode and the
boiler switches off.
The first stage of the indicator lamp for the suction per-
formance starts to flash more slowly as with the normal
switch-on of the suction indicators.
There are the following options for recommissioning:
Illustration
 Switch the main switch off and back on.
or
Illustration
Illustration
 Push the steam button or suction button for at least
3 seconds.
Illustration
 Push the main switch.
Illustration
 Separate the mains cable from the power supply
system.
Illustration
 Disconnect the steam plug from the appliance.
Hold the steam plug lock down and pull the steam
plug out of the appliance connector.
ATTENTION
Material damage due to a lack of cleaning the accesso-
ries after use.
 Always thoroughly clean all accessories prior to
storing the appliance.
 Disconnect all accessories.
 Rinse all accessories with clear water under a tap.
 Rinse pipes and steam suction hose with clear wa-
ter using the pipe cleaning brush.
 Allow accessories to dry afterwards.
 Store the appliance at a dry and frost-proof location.
Illustration
 Lift the handle of the water container.
 Pull out the water filter container.
Illustration
 Turn the handle towards the back.
 Remove the water filter insert.
Illustration
 Draining the water filter container by tilting it to-
wards the pouring device.
Illustration
 Pull the pipe bend off the filter casing with the grid
with the micro-perforation until it is completely re-
moved.
 Remove all components and rinse them under run-
ning water.
Replace filter in case of damage.
Please contact the authorised customer service in
order to purchase a new filter.
ATTENTION
Material damage due to incorrect installation of the pipe
bend in the filter with the micro-perforation.
 Upon installation insure that the arrow on the pipe
bend matches the marking on the filter with the mi-
cro-perforation.
Illustration
 Reinsert the water filter insert into the water filter
container.
Illustration
 Insert the water filter container into the appliance
using the handle.
Illustration
 Move the handle to its original position until it locks
in place.
Illustration
 Evenly roll up the power cable and place it in the
power cable compartment.
Illustration
 Put the water filter container back in its position and
ensure that it is properly placed.
 Please read the cleaning instructions of the manu-
facturer before treating leather, special fabrics and
wooden surfaces and always do a trial on a sample
or some hidden part. Let the steam-treated surface
dry and then check whether there are any changes
to the colour or form on account as reaction to the
steam.
 We recommend that you be very careful while
cleaning wooden surfaces (furniture, doors, etc.)
because long exposure to steam can damage the
wax coating, the finish or the surface colours.
Hence we recommend that you use steam only for
short intervals or first clean the surface with a cloth
that has been steam-moistened.
 For highly sensitive surfaces (for e.g. synthetic ma-
terials, painted surfaces, etc.) we recommend that
you use the steam function at the minimum perfor-
mance level.
 Cleaning of stainless steel: Avoid the use of abra-
sive brushes. Use hand nozzle with rubber lip or
detail nozzle without a round brush.
 Always test the compatibility of the fabrics on a hid-
den spot prior to treating them with the appliance:
Steam first, then allow to dry before checking for
colour changes or deformation.
ATTENTION
Material damage if the setting of the steam level is too high.
 Sensitive floors, such as parquet floors may only be
cleaned with the highest suction performance and
minimum steam level.
Putting Down the Accessories
Energy saver mode
Finish operation
Storing the Appliance
Emptying and cleaning the water filter container
How to Use the Accessories
Refreshing textiles
Floor nozzle
21EN

Kärcher SV 7 Specifications

General

Type	Cylinder steam cleaner
Capacity	1.2 L
Cord length	6 m
Product color	Black, Silver, Yellow
Boiler power	1100 W
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Ready time	5 min
Steam pressure	4 bar
Adjustable steam	Yes
Cleaning surfaces	Carpet, Hard floor, Laminate, Tiles
Continuous steam performance	65 g/min
Steam-ready light	-

Weight and Dimensions

Depth	510 mm
Width	330 mm
Height	340 mm
Weight	9100 g
Package weight	15600 g