Do you have a question about the Kawai AnyTime X GP and is the answer not in the manual?
Explains how to switch between Standard and Silent Play modes.
Provides step-by-step instructions for safely removing the action unit.
Details the procedure for adjusting the stop rail height and let-off.
Explains how to adjust the sensor height for optimal sound emission and muting.
Guides on adjusting the drawer-style controller for proper fit and operation.
Details how to adjust pedal sensors for correct timing and effects.
Explains how to adjust the transducer for optimal soundboard speaker performance.
Covers the replacement and adjustment of the drive lever for muting performance.
Instructions on how to enter diagnostic check modes.
Procedure to verify switch and pedal sensor functionality.
Steps to check the functionality of the LCD display.
Verifies keyboard and MIDI port connectivity and function.
Checks if all keys emit sound across the entire tone range.
Verifies correct sound output for left and right channels.
Tests the hammer sensor for proper detection of key presses.
Corrects uneven volume levels between keys.
Displays the current software version and checksum.
Troubleshooting steps for issues when the unit does not turn on.
Troubleshooting for controller display and switch malfunctions.
Troubleshooting for pedal malfunction in electronic sound play.
Troubleshoots issues with no acoustic or electronic sound output.
Addresses noise issues before hammer strike or sticking.
Solves problems where acoustic sound is emitted despite muting.
Addresses issues related to key touch feel and smoothness.
Troubleshoots problems with mute lever, action extraction, etc.
Solves issues related to the soundboard speaker operation.
Instructions for assembling the controller unit.
Steps for installing the various Printed Circuit Board units.
Assembly instructions for the D-sub connector box.
Assembly instructions for the sensor units.
Assembly instructions for the stop rail components.
Assembly instructions for the stop rail arm components.
Assembly instructions for the stop rail bracket.
Assembly instructions for the drive rod.
Assembly instructions for the drive lever.
Instructions for assembling the action unit components.
Steps for installing the controller and mute lever.
Assembly instructions for the speaker enclosure.
Assembly instructions for the actuator (transducer).
Provides a block diagram of the GP-ATX(-f) system.
Details cable wiring for the SP_set on GP-ATX(GA,GB).
Specifies cable wiring for the Sound System Assy on GP-ATX(GA,GB).
Details cable wiring for the Control Box Unit Assy on GP-ATX(GA,GB).
Part 1 of 6 for the GP-ATX GA KEP-326 (1) circuit diagram.
Part 2 of 6 for the GP-ATX GA KEP-326 (1) circuit diagram.
Part 3 of 6 for the GP-ATX GA KEP-326 (1) circuit diagram.
Part 4 of 6 for the GP-ATX GA KEP-326 (1) circuit diagram.
Part 5 of 6 for the GP-ATX GA KEP-326 (1) circuit diagram.
Part 6 of 6 for the GP-ATX GA KEP-326 (1) circuit diagram.
Circuit diagram for GP-ATX GA KEP-267 (2).
Circuit diagram for GP-ATX GA KEP-268,274 (1).
Circuit diagram for GP-ATX GA KEP-269,270,271 (1).
Circuit diagram for GP-ATX GA KEP-271 (1/1).
Part 1 of 2 for GP-ATX GA KEP-276 (2) circuit diagram.
Part 2 of 2 for GP-ATX GA KEP-276 (2) circuit diagram.
Circuit diagram for GP-ATX GA KEP-099 (4) (1/1).
Part 1 of 4 for GP-ATX GA KKB-036 (1) (A) circuit diagram.
Part 2 of 4 for GP-ATX GA KKB-036 (1) (B) circuit diagram.
Part 3 of 4 for GP-ATX GA KKB-036 (1) (C) circuit diagram.
Part 4 of 4 for GP-ATX GA KKB-036 (1) (D) circuit diagram.
Part 1 of 4 for GP-ATX GB KKB-037 (1) (A) circuit diagram.
Part 2 of 4 for GP-ATX GB KKB-037 (1) (B) circuit diagram.
Part 3 of 4 for GP-ATX GB KKB-037 (1) (C) circuit diagram.
Part 4 of 4 for GP-ATX GB KKB-037 (1) (D) circuit diagram.
Assembly specification diagram for PWB GP-ATX GA KKB-036 (1).
Assembly specification diagram for PWB GP-ATX RX2 KKB-037 (1).
Part 1 of 2 of assembly specification for PWB GP-ATX KEP-326 (1).
Part 2 of 2 of assembly specification for PWB GP-ATX KEP-326 (1).
Assembly specification for PCB GP-ATX KEP-276 (2) (1/1).
Assembly specification for PWB KEP-267 (2) (1/1).
Assembly specification for PWB KEP-268-277 (4) (1/1).
Explains how to switch between Standard and Silent Play modes.
Provides step-by-step instructions for safely removing the action unit.
Details the procedure for adjusting the stop rail height and let-off.
Explains how to adjust the sensor height for optimal sound emission and muting.
Guides on adjusting the drawer-style controller for proper fit and operation.
Details how to adjust pedal sensors for correct timing and effects.
Explains how to adjust the transducer for optimal soundboard speaker performance.
Covers the replacement and adjustment of the drive lever for muting performance.
Instructions on how to enter diagnostic check modes.
Procedure to verify switch and pedal sensor functionality.
Steps to check the functionality of the LCD display.
Verifies keyboard and MIDI port connectivity and function.
Checks if all keys emit sound across the entire tone range.
Verifies correct sound output for left and right channels.
Tests the hammer sensor for proper detection of key presses.
Corrects uneven volume levels between keys.
Displays the current software version and checksum.
Troubleshooting steps for issues when the unit does not turn on.
Troubleshooting for controller display and switch malfunctions.
Troubleshooting for pedal malfunction in electronic sound play.
Troubleshoots issues with no acoustic or electronic sound output.
Addresses noise issues before hammer strike or sticking.
Solves problems where acoustic sound is emitted despite muting.
Addresses issues related to key touch feel and smoothness.
Troubleshoots problems with mute lever, action extraction, etc.
Solves issues related to the soundboard speaker operation.
Instructions for assembling the controller unit.
Steps for installing the various Printed Circuit Board units.
Assembly instructions for the D-sub connector box.
Assembly instructions for the sensor units.
Assembly instructions for the stop rail components.
Assembly instructions for the stop rail arm components.
Assembly instructions for the stop rail bracket.
Assembly instructions for the drive rod.
Assembly instructions for the drive lever.
Instructions for assembling the action unit components.
Steps for installing the controller and mute lever.
Assembly instructions for the speaker enclosure.
Assembly instructions for the actuator (transducer).
Provides a block diagram of the GP-ATX(-f) system.
Details cable wiring for the SP_set on GP-ATX(GA,GB).
Specifies cable wiring for the Sound System Assy on GP-ATX(GA,GB).
Details cable wiring for the Control Box Unit Assy on GP-ATX(GA,GB).
Part 1 of 6 for the GP-ATX GA KEP-326 (1) circuit diagram.
Part 2 of 6 for the GP-ATX GA KEP-326 (1) circuit diagram.
Part 3 of 6 for the GP-ATX GA KEP-326 (1) circuit diagram.
Part 4 of 6 for the GP-ATX GA KEP-326 (1) circuit diagram.
Part 5 of 6 for the GP-ATX GA KEP-326 (1) circuit diagram.
Part 6 of 6 for the GP-ATX GA KEP-326 (1) circuit diagram.
Circuit diagram for GP-ATX GA KEP-267 (2).
Circuit diagram for GP-ATX GA KEP-268,274 (1).
Circuit diagram for GP-ATX GA KEP-269,270,271 (1).
Circuit diagram for GP-ATX GA KEP-271 (1/1).
Part 1 of 2 for GP-ATX GA KEP-276 (2) circuit diagram.
Part 2 of 2 for GP-ATX GA KEP-276 (2) circuit diagram.
Circuit diagram for GP-ATX GA KEP-099 (4) (1/1).
Part 1 of 4 for GP-ATX GA KKB-036 (1) (A) circuit diagram.
Part 2 of 4 for GP-ATX GA KKB-036 (1) (B) circuit diagram.
Part 3 of 4 for GP-ATX GA KKB-036 (1) (C) circuit diagram.
Part 4 of 4 for GP-ATX GA KKB-036 (1) (D) circuit diagram.
Part 1 of 4 for GP-ATX GB KKB-037 (1) (A) circuit diagram.
Part 2 of 4 for GP-ATX GB KKB-037 (1) (B) circuit diagram.
Part 3 of 4 for GP-ATX GB KKB-037 (1) (C) circuit diagram.
Part 4 of 4 for GP-ATX GB KKB-037 (1) (D) circuit diagram.
Assembly specification diagram for PWB GP-ATX GA KKB-036 (1).
Assembly specification diagram for PWB GP-ATX RX2 KKB-037 (1).
Part 1 of 2 of assembly specification for PWB GP-ATX KEP-326 (1).
Part 2 of 2 of assembly specification for PWB GP-ATX KEP-326 (1).
Assembly specification for PCB GP-ATX KEP-276 (2) (1/1).
Assembly specification for PWB KEP-267 (2) (1/1).
Assembly specification for PWB KEP-268-277 (4) (1/1).
| Brand | Kawai |
|---|---|
| Model | AnyTime X GP |
| Category | Musical Instrument |
| Language | English |