Kenmore 110.44832 200 User Manual

Sears Kenmore/Whirlpool Front Load Washer
Error Codes: 02F dLF
Model: 110.44832 200 (110. = Whirlpool)
S/N: CSP 1903874
Type: 199-AKP 705/WT
SOURCE: www.applicancepartspros.com
WHIRLPOOL FAULT CODES
Whirlpool Duet Front Loading Automatic Washer Fault Codes
Failure
Code
Fault Code Description Solution
FH No water detected entering
machine or Pressure switch trip
not detected.
If after 30 seconds the control does not detect water
entering machine and then valves will be turned off and
the error code will be displayed.
Or
If the control has turned the water valves on and after 8
minutes the flow meter has detected 10.5 gallons of
water passing through it, but has not detected the
pressure switch trip, the valves will be turned off and the
error code will flash.
Press PAUSE/CANCEL twice to clear the display.
Potential Causes
• If there is no water in the unit:
- Make sure that both valves at the water source(s) are
turned on all the way.
- Check for plugged or kinked inlet hoses or plugged
screens in the inlet valves
- Verify inlet valve operation
• If there is water in the unit:
- Verify Drain pump operation
- Pressure Switch Hose is in good condition and
properly connected to Tub and Pressure switch
• Verify there is not a siphon problem
• Verify wire harness connections to; Inlet Valves,
Pressure Switch, Drain Pump, Flow Meter, and Central
Control Unit (CCU)
• Check all hoses for possible leaks
• Verify pressure switch operation
• Verify flow meter operation
• Verify CCU operation
Replace failed component.
F02 Long Drain If the drain time exceeds 8 minutes, the water valves are
turned off and F02 is flashed.
Press PAUSE/CANCEL twice to clear the display.
NOTE: After 4 minutes the “Sud” error will be displayed,

Kenmore 110.44832 200 Specifications

General

Brand	Kenmore
Model Number	110.44832200
Type	Top Load Washer
Spin Speed	700 RPM
Color	White
Control Type	Electronic
Width	27.5 inches
Depth	27 inches

Summary

Whirlpool Front Load Washer Fault Codes

FH: No Water Detected

Error code FH indicates no water detected or pressure switch trip not detected. Solution involves checking water supply and inlet valves.

F02: Long Drain

Error code F02 signifies a long drain time exceeding 8 minutes. Checks include drain hose, pump, and electrical connections.

Troubleshooting Washer Errors

F05: Water Temperature Sensor Error

Error F05 occurs if the water temperature sensor is out of range or heating element circuit fails. Check sensor, heating element, and relay.

F06: Drive Motor Tachometer Error

Error F06 means the control cannot detect motor speed. Check wire harness, drive motor, MCU, and CCU.

F07: Motor Control Unit Error

Error F07 indicates a short in the motor control unit. Verify wire harness connections to MCU, motor, and CCU.

F09: Overflow Condition

Error F09 signals an overflow condition if the pressure switch contact stays closed for over 60 seconds.

Advanced Washer Diagnostics

F10: MCU Heat Sink Thermal Trip

Error F10 occurs if the MCU heat sink thermal protector trips, stopping motor functions. Check installation and ventilation.

F11: Serial Communication Error

Error F11 means communication between CCU and MCU failed. Check wire harnesses and system components.

F13: Dispenser Circuit Error

Error F13 indicates the dispenser motor cannot be driven properly. Check mechanical linkage and wiring.

F14: EEPROM Error

Error F14 occurs when CCU cannot read EEPROM data. A power glitch might be the cause; try resetting the unit.

Washer Operation and Error Resolution

F15: Motor Control Unit (MCU) Error

Error F15 occurs if MCU detects multiple resets or errors. Check MCU, motor, and drive belt for issues.

Sud: Suds Lock

Error 'Sud' indicates a suds lock condition due to excessive detergent or load. Run a rinse/spin cycle.

FdL: Door Lock Error

Error FdL means the door cannot be locked. Check the door lock mechanism, switch assembly, and wiring.

FdU: Door Unlock Error

Error FdU indicates the door cannot be unlocked. Check the door lock/switch assembly and wiring.