To Next PageTo Next PageHow to fix water leaks in a Kenmore Water Heater?
If your Kenmore Water Heater is leaking from improperly sealed connections, such as the hot or cold supply, relief valve, drain valve, or thermostat threads, try tightening these connections. Also, inspect other appliances near the water heater for leaks. If the issue is condensation, refer to the CONDENSATION section.
Why is the T&P valve leaking on my Kenmore 153.336466 Water Heater and how to fix it?
If the T&P valve on your Kenmore Water Heater is leaking due to thermal expansion in a closed water system, install a thermal expansion tank. Do not plug the T&P valve. If the valve is improperly seated, check the relief valve for proper operation, again, do not plug the T&P valve.
How to troubleshoot a Kenmore 153.336466 Water Heater when the pilot won't light?
If your Kenmore Water Heater pilot will not light, turn on the main gas shutoff valve if the main gas supply is off. If the gas control knob is not positioned correctly, refer to the LIGHTING INSTRUCTIONS. Adjust the igniter tip if it is more than 1/8" from the pilot hood. Replace the pilot assembly if there is a thermocouple or thermocouple TCO malfunction. Reconnect the wire connector to the spark igniter if the wire is disconnected. Replace the pilot assembly if the electrode or electrical wire is broken. Replace the Piezo Igniter generator if it fails to operate or malfunctions. For melted insulation on the igniter wire or a high ambient room temperature, contact Sears Service to determine the cause.
What to do if the burner will not stay lit on my Kenmore 153.336466?
If the burner on your Kenmore Water Heater won't stay lit, replace the pilot assembly if there is a thermocouple TCO malfunction. Clean and reinstall the air intake screen if it is dirty or clogged. Replace the Gas Control if it is defective. Contact a service agency to determine the cause if there is a high ambient room temperature. Contact Sears Service to determine the cause if the flame arrestor openings are blocked.
Why does the pilot light keep going out on my Kenmore 153.336466?
If the pilot light keeps going out on your Kenmore Water Heater, clean the pilot assembly if the pilot burner is dirty. Also, clean and reinstall the air intake screen if it is dirty or clogged. Insert the thermocouple correctly if the thermocouple tip is not in contact with the pilot flame. Replace the pilot assembly if there is a thermocouple or thermocouple TCO malfunction. Replace the Gas Control if it is defective.
What to do if my Kenmore 153.336466 Water Heater is not producing enough hot water?
If you're not getting enough hot water from your Kenmore Water Heater, make sure the heater is lit and the thermostat is on. If not, refer to the LIGHTING INSTRUCTIONS. Ensure the thermostat isn't set too low by referring to TEMPERATURE REGULATION. If the heater is undersized, reduce hot water usage. For low gas pressure, contact your gas supplier. If the incoming water is unusually cold, allow more time for the heater to reheat. Have a plumber check and repair any leaks in hot water pipes or fixtures. If the high-temperature limit switch is activated, contact Sears Service to determine the cause.
How to get rid of smelly odors from a Kenmore Water Heater?
To address smelly odors from your Kenmore Water Heater, drain and flush the heater thoroughly, then refill if there is high sulfate or mineral content in the water supply. If bacteria are present in the water supply, chlorinate or aerate the water supply.
What to do if my Kenmore 153.336466 is producing water that is too hot?
Refer to TEMPERATURE REGULATION if your Kenmore Water Heater's thermostat is set too high.
Why is my Kenmore Water Heater making sizzling or rumbling noises?
To address sizzling or rumbling sounds in your Kenmore Water Heater, clean sediment from the tank. Refer to the DRAINING instructions in the Maintenance section of the manual.
General| Brand | Kenmore |
|---|---|
| Model | 153.336466 |
| Category | Water Heater |
| Language | English |
Provides emergency steps to take if a gas leak is detected.
Defines key terms like Gas Supplier for clarity.
Warns about flammable vapors, ignition sources, and improper operation.
Alerts to risks of carbon monoxide and proper venting requirements.
Warns about scald hazards and potential tank explosion from overheating.
Highlights risks of property damage due to incorrect installation or use.
Lists required materials for installation.
Lists essential and specialized tools for installation.
Step-by-step guide to safely disconnect and remove the existing unit.
Details crucial factors for choosing a safe and efficient installation location.
Explains requirements for air supply for combustion and ventilation.
Covers connecting water lines, relief valve, and pipe insulation.
Details requirements for venting flue gases and connecting gas supply.
Explains the purpose and installation of sediment traps in gas lines.
Crucial safety steps before and during appliance startup, including gas leak detection.
Step-by-step guide for safely lighting the pilot and main burner.
Explains risks of hot water scalds and recommended temperature settings.
Instructions for removing sediment to prevent tank failure and maintain performance.
Guidelines for checking the vent system for safety and efficiency.
Procedures for inspecting and cleaning the burner for proper combustion.
Covers general upkeep like housekeeping, anode rod checks, and draining.
Details on how to test and maintain the safety relief valve.
Steps for replacing the washer in the drain valve.
How to contact Sears Service for repairs.
Addresses issues encountered during initial startup and operation.
Explains condensation phenomena and normal operating noises.
Verifies the proper function of the draft hood for safe operation.
Identifies causes and solutions for smoke, rotten egg smells, and air in faucets.
Explains the automatic safety shut-off mechanism and its reset procedure.
Guides users on identifying and diagnosing leaks from various parts of the unit.
Information on obtaining warranty service and making claims.
Details on extended service plans and professional installation options.
