Kenmore 253.76110 - User Manual

22 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Use & Care Guide

Manual de Uso y Cuidado

Engish / Espaiol

_.) _'_l"

Kenmore Elite

_=I'=® °' _'<_ I °'

Models/Modelos: 253.76080, 253.76110, 253.76120, 253.76150

P/N 2020215A1010

Sears Brands Management Corporation

Hoffman Estates, IL 60179 U.S.A.

www.kenmore.com

www.sears.com

www.kmart.com

®

Table of Contents

Questions and Answers

M
Michael ChristensenAug 16, 2025
What to do if Kenmore 253.76110 doesn't cool the room and there is ice behind front panel?
- J
  Joseph FigueroaAug 16, 2025
  If your Kenmore Air Conditioner does not cool the room and there is ice behind the front panel, consider the following: * If the outside temperature is below 16 °C, set the mode to FAN ONLY and the fan speed to the fastest setting to defrost the coil. * If the filter is dirty, open the front panel, remove the filter, rinse or vacuum it, replace it, and close the panel. * If the BTU size is too large, a lower capacity unit may be required depending on the size of the room being cooled.
K
Kathleen NicholsAug 20, 2025
What to do if my Kenmore 253.76110 Air Conditioner will not operate?
- M
  Martha StanleyAug 20, 2025
  If your Kenmore Air Conditioner won't operate, check these potential causes: * Ensure the power supply cord is firmly pushed into a live wall outlet with the correct voltage. * Replace any blown fuse with a time delay type or reset the circuit breaker. * Press the ON/OFF button to ensure the unit is turned ON. * Adjust the temperature to a lower setting if it's warmer than the room temperature. * Allow 3 minutes for the compressor to restart if the unit was recently turned OFF and ON. * Press the ON/OFF button if the timer shut the unit OFF. * If the touch pad and remote are unresponsive, unplug the unit for 10 seconds to reset the controls. * Press the RESET button on the plug head if the power cord has tripped.
R
Richard OnealAug 23, 2025
Why does my Kenmore 253.76110 keep blowing fuses or tripping the circuit breaker?
- C
  cassandrarhodesAug 23, 2025
  If your Kenmore Air Conditioner blows fuses or trips the circuit breaker, try these solutions: * Replace the fuse with a time delay type or reset the circuit breaker. * Unplug or relocate some electrical devices that share the same circuit. * Ensure the unit is plugged into a single circuit outlet if it's rated over 7.5 amps. * Do not use an extension cord to run the unit. * Turn the unit OFF and wait 3 minutes before restarting if it was turned OFF and ON too quickly.
M
Michelle MathewsAug 27, 2025
Why does my Kenmore 253.76110 Air Conditioner turn on and off by itself?
- S
  Steven GriffinAug 27, 2025
  If your Kenmore Air Conditioner turns on and off by itself, it could be due to these reasons: * When the outside temperature is extremely hot, set the fan speed at the fastest setting for maximum cooling. * If the ENERGY SAVER feature is on, note that it doesn't circulate air continually; switch to COOL mode for constant air circulation. * If the timer turned the unit ON or OFF, use the ON/OFF button to control the unit.
A
Aaron HarrisAug 31, 2025
Why is my Kenmore 253.76110 Air Conditioner running too much?
- S
  Stephanie VincentAug 31, 2025
  If your Kenmore Air Conditioner runs too much, here's what might be happening: * When Energy Saver mode is active, the inside blower continues operating for one minute to use as much cooling as available in the evaporator. * If you've replaced an older unit, the newer, higher efficiency air conditioner may run longer to cool the room, but total energy consumption is less due to the higher efficiency. * If the BTU size is too small, you might need a higher capacity unit depending on the room size.
J
Jose MedinaSep 3, 2025
Why is my Kenmore 253.76110 Air Conditioner dripping water inside the room?
- B
  benjamin41Sep 3, 2025
  If water is dripping from your Kenmore Air Conditioner inside the room, it's likely due to improper installation. The unit should be mounted on a 1/4" downward slope to the outside (1/2 bubble on a carpenter’s level) to ensure proper drainage. Reposition or shim the cabinet as needed, but do not drill the drain pan.
D
Dana BrightSep 7, 2025
Why will the remote not operate my Kenmore Air Conditioner?
- R
  Richard PayneSep 7, 2025
  If the remote will not operate your Kenmore Air Conditioner, verify that the batteries are installed properly. Also, the remote may not work properly when used at extreme angles to the front of the unit.
L
Lisa PerezNov 11, 2025
What to do if Kenmore 253.76110 Air Conditioner doesn't cool the room but there is no ice behind front panel?
- S
  Sean GilmoreNov 11, 2025
  If your Kenmore Air Conditioner isn't cooling the room and there's no ice behind the front panel, consider the following: * Clean or replace the filter by opening the front panel, removing the filter, rinsing or vacuuming it, replacing it, and closing the panel. * Set the temperature to a lower setting if it is warmer than the current room temperature. * Note that the unit isn't designed to cool if the room temperature is below 16 °C. * Ensure that furniture, drapes, blinds, or other obstructions are cleared from the front of the unit. * Ensure that leaves, dirt, branches, or other obstructions are cleared from the back of the unit. * Close any open doors, windows, registers, etc. * Allow sufficient time for cooling if the unit was recently turned on, especially in a larger ...

Kenmore 253.76110 Specifications

General

Brand	Kenmore
Model	253.76110
Category	Air Conditioner
Language	English

Related product manuals

Kenmore 253.76125

Kenmore 253.76180

Kenmore 253.76120

Kenmore 253.76150

Kenmore 253.76185

Kenmore Elite 253.76135

Kenmore 253.76223

Kenmore 253.76080

Kenmore 253.76250

Kenmore Elite 253.76085

Kenmore Elite 253.76062

Preview: Kenmore 253.70051

Kenmore 253.70051