How to resolve OE Error on Kenmore Dishwasher?
An OE Error on your Kenmore dishwasher signals a drainage problem. Check for a clogged, kinked, or frozen drain hose. Also, inspect and clean the air gap or disposal, and ensure the filters are clean.
Why is my Kenmore Dishwasher leaking in front of unit?
If your Kenmore dishwasher is leaking in the front, it might not be leveled properly. Verify that the unit is level from side to side and from front to back. Also, the wrong detergent could be causing excessive sudsing. If this is the case, allow the foam to subside for 24 hours, then clean the inside of the tub with milk.
Why aren’t dishes drying in my Kenmore 722.1435 Dishwasher?
If dishes aren’t drying in your Kenmore dishwasher, the rinse agent dispenser might be empty. Check and refill it if necessary.
What to do if Kenmore 722.1435 Dishwasher continuously beeps when the door is opened?
If your Kenmore Dishwasher continuously beeps when the door is opened, during or right after a cycle has completed, the contents of the dishwasher are hot and care should be used when placing your hands inside the dishwasher. Close the door until the dishwasher and dishes have cooled down.
Why does my Kenmore Dishwasher have spots and filming on dishes?
Spots and filming on dishes in your Kenmore dishwasher can occur due to several reasons: * Low water temperature: Ensure the water supply is at least 120 °F. * Incorrect detergent amount: Use the recommended amount of detergent. * Overloading: Avoid overloading the dishwasher. * Improper loading: Refer to the Operation section for correct loading. * Insufficient water pressure: Maintain water pressure between 20 and 80 psi. * Insufficient detergent: Add the recommended amount of detergent. * Empty rinse aid dispenser: Refill the rinse aid dispenser. * Hard water buildup: Remove dishes and use citric acid powder to clean the tub.
Why spray arms do not rotate smoothly in my Kenmore 722.1435 Dishwasher?
If the spray arms in your Kenmore dishwasher do not rotate smoothly, the holes of the spray arms may be blocked by food particles. Clean the holes of the spray arms.
What to do if Kenmore 722.1435 chimes if panel is touched during operation?
If your Kenmore Dishwasher chimes if panel is touched during operation, bumping into or touching the control panel during operation may result in a disabled button sound. Button sounds can be turned off by pressing and holding Mixed Load and Sani Rinse for three seconds.
Why lamps do not illuminate on my Kenmore Dishwasher?
If the lamps on your Kenmore dishwasher do not illuminate, the power is not connected. Connect the power supply.
How to resolve IE Error on Kenmore 722.1435 Dishwasher?
An IE Error on your Kenmore dishwasher indicates a water inlet problem. Check for a clogged, kinked, or frozen water inlet hose and verify the water supply.
Why does my Kenmore 722.1435 smell?
An odor in your Kenmore dishwasher could be due to a few reasons: * If a cycle was stopped early, residual water might remain. Turn on the power and follow the instructions for Canceling a Cycle to remove the water. Then, run the Accela Wash cycle with detergent but an empty dishwasher. * Food may be in the bottom of the unit or in the filter. Clean the filter and the interior. * Unwashed dishes left for too long can cause odor. Run a cycle with one cup of white vinegar in a dishwasher-safe glass or bowl on the top rack.
Details the warranty against defects in material or workmanship for one year from the sale date.
Covers lifetime replacement for stainless steel tub/inner door panel rust-through.
Crucial safety precautions to follow when operating the dishwasher.
Instructions for proper grounding and electrical safety to prevent shock hazards.
Provides a schedule for cleaning dishwasher filters based on usage and washing habits.
Explains how to add detergent to compartments based on water hardness and recommends types.
Details available wash cycles and options for models with steam functionality.
Details available wash cycles for models without steam functionality.
Addresses problems like non-operation, slow cycles, and odor.
Solutions for food soil, cloudiness, marks, and spots on dishes.
Troubleshooting for beeping, cycle cancellation, leaking, and display errors.
Explains error codes related to water inlet and drainage problems.
Solutions for errors caused by oversudsing, leakage, heater, and thermistor issues.
Addresses error codes associated with motor or vario motor issues.
General| Type | Built-In |
|---|---|
| Control Type | Electronic |
| Number of Wash Cycles | 6 |
| Number of Options | 4 |
| Energy Star Certified | Yes |
| Soil Sensor | Yes |
| Delay Start | Yes |
| Third Rack | No |
| Stainless Steel Tub | Yes |
| Heated Dry | Yes |
| Width | 24 inches |
To Next Page