T
Timothy MckenzieAug 31, 2025
How do I resolve a 'Connection Error' on my Kenwood Car Video System?
- JJoshua DanielsAug 31, 2025
If your Kenwood Car Video System displays a “Connection Error”, connect the registered device.
To Next PageTo Next PageHow do I resolve a 'Connection Error' on my Kenwood Car Video System?
If your Kenwood Car Video System displays a “Connection Error”, connect the registered device.
Why does my Kenwood Car Video System display 'Authorization Error'?
If your Kenwood Car Video System shows an “Authorization Error”, check if the connected iPod/iPhone is compatible with the unit.
What to do if no picture is displayed on the screen of my Kenwood Car Video System?
If no picture is displayed on the screen of your Kenwood Car Video System, turn on the screen.
How to troubleshoot a Kenwood Car Video System remote controller that does not work?
If the remote controller for your Kenwood Car Video System is not working, replace the battery.
How to fix 'Miswiring DC Offset Error' or 'Warning DC Offset Error' on Kenwood Car Video System?
If your Kenwood Car Video System displays “Miswiring DC Offset Error” or “Warning DC Offset Error”, it indicates that a speaker cord has shorted or is in contact with the car chassis. Wire or insulate the speaker cord as needed, and then reset the unit.
What to do if my Kenwood Car Video System displays 'USB Device Error'?
If your Kenwood Car Video System shows a “USB Device Error”, try the following: * Turn the unit off and then on again. * Connect a different USB device.
What to do if my Kenwood Car Video System doesn't work at all?
If your Kenwood Car Video System is completely unresponsive, try resetting the unit.
Why is there static noise while listening to the radio on my Kenwood Car Video System?
If you are experiencing static noise while listening to the radio on your Kenwood Car Video System, make sure the antenna is firmly connected.
What to do if my Kenwood Car Video System displays 'No Signal'?
If your Kenwood Car Video System shows a “No Signal” message: * Start playback on the external component connected to the AV-IN input terminal. * Check the cords and connections. * The signal input may be too weak.
General| Display Size | 6.2 inches |
|---|---|
| Resolution | 800 x 480 pixels |
| Touchscreen | Yes |
| DVD Player | Yes |
| USB Port/Input | Yes |
| Bluetooth | Yes |
| iPod/iPhone Compatibility | Yes |
| Rear View Camera Input | Yes |
| Audio Formats Supported | MP3, WMA, AAC |
| AM/FM Tuner | Yes |
| Steering Wheel Control Compatible | Yes |
| Preamp Outputs | 3 (Front, Rear, Subwoofer) |
| Power Output | 50 Watts x 4 |
| RMS Power Output | 22W x 4 |
| Peak Output | 50W x 4 |
| Video Formats Supported | MPEG-1, MPEG-2, DivX |
Procedure to reset the unit to factory settings.
Guide to initial setup procedures like language, AV input, and panel color.
Steps to activate the security indicator to protect the receiver.
Procedures for turning the unit on/off, standby, and controlling the screen.
How to adjust audio volume and attenuate sound.
Guide to choosing different audio/video sources like NAV, DISC, USB, iPod, TUNER, VIDEO, Bluetooth.
How to play files from a USB mass storage device.
Steps for connecting a USB device and safety precautions.
Connecting the iPod/iPhone and required cables.
Adjusting sound equalization using preset modes or manual customization.
Steps to activate the rear view camera and how it is displayed.
General information and precautions for using Bluetooth devices.
Solutions for common problems and error messages like "No Signal" or "Connection Error".
Technical details of the display, DVD player, USB, and Bluetooth interfaces.
Important warnings and advice for safe and correct installation.
