Kenwood VR-208 User Manual

PORE IIIS
MLLER SPRAY AILELISEDESELOLECSLBRERL sobteeomeneRe7! Fines EIGER Ce
input level adjustment (analog sources only)
If
the
input
level
of
an
analog
source
signal
is
too
high
or
the
receiver's
CLIP
INDICATOR
lights.
adjust
the
input
level.
@
Use
the
INPUT
SELECTOR
knob
to
select
the
source
who's
input
level
you
want
to
adjust.
*
You
can
store
a
separate
input
/evel
for
each
input
source.
If
the
MONITOR
function
is
on,
you
can
store
an
input
level
for
when
MONITOR
is
on
independently
of
the
input
levels
for
the
input
sources.
© Press the SOUND key several times until the “INPUT” indication
appears.
© Use the MULTI CONTROL (TUNING/SKIP) to adjust the input
level so that the CLIP INDICATOR no longer lights.
je
GOB
TACIT
|
mo:
| Oo Oaivr tt oy 7
¢
The
adjustment
mode
is
displayed
for
approximately
eight
sec-
onds.
¢ The input level may be adjusted to any one of three settings: 0.
-3, and -6. (The initial setting is 0.)
@ Press the SOUND key to return to the input indication.
* If you used the remote control to perform the above setting, press
the VIDEO key at this point to turn off the remote control's own
adjustment mode. In this case. the input source is not switched.
Preparing for playback
SN rn CoN Labs Ss BRS a ct
Some preparatory steps are needed before starting playback.
(INPUT MODE
ON/STANDBY AUTO
|
=o 18
ode
OG.)
iNPUT SELECTOR
SPEAKERS A/B
PERE CCR RELIANT ee BOSE ES ANN ck MT NR itt
Turning on the receiver
@ Turn on the power to the related components.
@ Turn on the power to this receiver by pressing POWER (and ON/
STANDBY) key(s).
FERRIES LES NOIRE LIES LEGGE LLG ELSES NA OBES EIU ES LEN i OBE CELINA Nt tc acm
Selecting TAPE/MD
Select the source name corresponding to the component connected
to the MD/TAPE jacks. The initial factory setting is "TAPE". To change
the source name associated with the MD/TAPE jacks to “MD.” foliow
the steos beiow:
@ Use the INPUT SELECTOR knob to select “TAPE”.
© Hold down the AUTO key for more than two seconds.
* The source indication changes to "MD".
* To return to the original indication, repeat the above procedure.
© You also will need to change the name input to the remote contro!
to “MD” RC- 3
RRR SS eh NE IN
Selecting the speaker system
Press the SPEAKERS A or B key to select the speaker system to
be used.
AON : Sound from the speakers connected to the SPEAKERS A
terminals on the rear panel.
BON : Sound from the speakers connected to the SPEAKERS B
terminalis on the rear panel.
: Sound from both the speakers connected to the SPEAK-
ERS A and B terminals on the rear panel.
A+B OFF : Nosound from the speakers. Use this setting when listen-
ing with headphones for stereo sound in all playback
modes.
A+B ON
elf you activate a surround mode. speaker system A is selected
automatically.
The
indicator
for
the
speakers
you
want
to
use
should
be
lit
Selecting the input mode |
If
you
have
selected
a
component
connected
to
the
VIDEO2
or
VIDEQ3
jacks,
make
sure
that
the
input
mode
setting
is
correct
for
the
type
|
of
audio
signal
to
be
used.
~

Kenwood VR-208 Specifications

General

Brand	Kenwood
Model	VR-208
Category	Stereo Receiver
Language	English