To Next PageTo Next Page
Need help?Do you have a question about the Kenwood VR-509 and is the answer not in the manual?
Audio Specifications| rated power output during stereo operation | 100 watts per channel minimum RMS, both channels driven, at 8 Ω from 20 Hz to 20 kHz with no more than 0.7% total harmonic distortion |
|---|---|
| effective power output during surround operation front | 100 W + 100 W |
| effective power output during surround operation center | 100 W |
| effective power output during surround operation surround | 100 W + 100 W |
| total harmonic distortion | 0.05% (1 kHz, 50W, 8 Ω) |
Video Specifications| video inputs/outputs composite | 1 Vp-p / 75 Ω |
|---|---|
| s video luminance signal | 1 Vp-p / 75 Ω |
| s video chrominance signal | 0.286 Vp-p / 75 Ω |
| component video luminance signal | 1 Vp-p / 75 Ω |
| component video CB/CR signal | +/– 0.324 Vp-p / 75 Ω |
FM Tuner Specifications| tuning frequency range | 87.5 MHz ~ 108 MHz |
|---|---|
| usable sensitivity mono | 1.3 µV (75 Ω)/ 13.2 dBf (75 kHz DEV., SINAD 30 dB) |
| 50dB quieting sensitivity stereo | 28 µV (75 Ω)/ 40.2 dBf |
| total harmonic distortion mono | 0.5% (65 dBf input) |
| total harmonic distortion stereo | 0.7% (65 dBf input) |
| signal to noise ratio mono | 75 dB (65 dBf input) |
| signal to noise ratio stereo | 68 dB (65 dBf input) |
| stereo separation | 40 dB |
| selectivity | 70 dB (±400 kHz) |
| frequency response | 30 Hz ~ 15kHz, +0.5 dB, –3.0 dB |
AM Tuner Specifications| tuning frequency range | 530 kHz ~ 1, 700 kHz (10 kHz step) |
|---|---|
| usable sensitivity | 16 µV / (600 µV/m) |
| signal to noise ratio | 50 dB (30% mod. 1 mV input) |
General Specifications| power consumption | 2.6 A |
|---|---|
| dimensions width | 440 mm (17-5/16") |
| dimensions height | 144 mm (5-11/16") |
| dimensions depth | 399 mm(15-11/16") |
| weight | 8.8 kg (19.4 lb) |
Digital Audio Specifications| sampling frequency | 32 kHz, 44.1 kHz, 48 kHz, 96kHz |
|---|---|
| input level/impedance/wave length optical | (-15 dBm ~ -21 dBm), 660 nm ±30nm |
| input level/impedance coaxial | 0.5 Vp-p / 75 Ω |
Explains the multi-mode operation of the remote control and the importance of understanding its design.
Instructions for carefully unpacking the unit and checking for shipping damage.
Critical warnings and cautions to prevent fire or electric shock.
FCC warning, RF energy notes, and CATV grounding guidelines.
Instructions on how to clean the unit using a soft, dry cloth.
Explains the four sections of the manual: Preparations, Operations, Remote Control, and Additional Information.
Introduction to various surround sound modes and technologies offered by the receiver.
Identifies and explains the functions of buttons and indicators on the receiver's front panel.
Explains the standby mode and how the system can be switched on using the remote control.
Identifies and explains the functions of all buttons on the remote control unit.
General instructions for connecting system components and initial setup procedures.
Explains how to select digital or analog input modes for various audio signals.
Diagrams and instructions for connecting various audio sources like CD players and record players.
Guidance on using S-VIDEO jacks for connecting video components.
Instructions and diagrams for connecting digital audio sources via optical and coaxial cables.
Instructions for connecting video components using COMPONENT VIDEO jacks for better picture quality.
Detailed instructions for connecting a DVD player with 6-channel output for surround sound.
Diagrams showing how to connect front, center, and surround speakers, including a powered subwoofer.
Step-by-step guide on connecting speaker wires using various terminal types and banana plugs.
Recommendations for optimal placement of front, center, and surround speakers for best sound.
Instructions for connecting camcorders or video games to the AV AUX jacks.
Guide for connecting AM and FM antennas for optimal reception.
Instructions for connecting KENWOOD audio components for system control operations.
How to register setup codes for compatible KENWOOD components.
Explanation of the RF remote control function and how to change transmission frequency.
Step-by-step instructions for loading batteries into the remote control.
Guide on using display operation keys for navigation and setup.
Instructions for connecting IR repeaters to control components in cabinets.
Instructions for connecting the RF remote antenna for optimal signal reception.
Steps to set up speakers (subwoofer, front, center, surround) for optimum surround sound.
How to adjust speaker volume levels using test tones and distance settings.
Guide for adjusting input levels for analog sources to prevent clipping.
Preliminary steps required before starting playback of audio sources.
How to select and listen to various audio source components using the receiver.
How to adjust tone controls (bass, treble), muting, and source direct playback.
Instructions on how to connect and use headphones with the receiver.
Steps for recording music from analog sources onto cassette decks or MD recorders.
Steps for recording digital audio sources using A-REC or M-REC modes.
Guide to tuning into AM and FM radio stations manually or automatically.
Steps to store favorite radio stations into memory presets.
How to sequentially receive preset radio stations using the P.CALL function.
Explanation of DTS, Dolby Digital, and Dolby Pro Logic II surround sound technologies.
Details on using Dolby 3 Stereo for systems without surround speakers.
Explanation of Digital Signal Processor modes for creating concert hall atmospheres.
How to select and play surround modes based on input signal type.
Guide to enjoying surround sound playback from DVD players with 6-channel output.
How to make further sound adjustments while listening in surround mode.
How to use Midnight mode for lower volume listening during Dolby Digital playback.
Adjusting dimension mode for balanced sound from all speakers in Pro Logic II Music.
How to adjust the subwoofer volume using the remote control.
How to adjust the brightness of the receiver's display.
Step-by-step guide to register setup codes for controlling external components.
How to operate registered components using the remote control.
How to change the remote control's operation mode without altering the input selector.
How to set up and create macros for sequential component operations.
How to execute a pre-programmed macro for automatic component operation.
Steps to delete registered setup codes for external components.
How to store remote control codes from other components into the universal remote.
How to reset setup codes and memories to their original factory default settings.
How to display CD TEXT data from a KENWOOD CD player on the remote's display.
General guide on operating other components using the remote control keys or display.
Specific remote control functions for operating satellite tuners.
Detailed functions for operating cassette decks using the remote control.
Detailed functions for operating CD players using the remote control.
Detailed functions for operating MD recorders using the remote control.
Detailed functions for operating TVs using the remote control.
Detailed functions for operating VCRs using the remote control.
Detailed functions for operating LD players using the remote control.
Detailed functions for operating DVD players using the remote control.
Detailed functions for operating DSS receivers using the remote control.
Detailed functions for operating cable tuners using the remote control.
Troubleshooting guide for common problems encountered with the amplifier section.
Troubleshooting common radio reception and interference problems.
Troubleshooting common issues related to the remote control unit's operation.
Technical specifications for the audio output, sensitivity, and frequency response.
Technical specifications for video inputs/outputs and tuner performance.
