Kenwood X700-5 - User Manual

9 pages

Save Page as PDF

To Next Page

Take the time to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the best performance from your new power

amplifier.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided

below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.

Model

X700-5 Serial number

US Residence Only

X700-5

5 CHANNEL POWER AMPLIFIER

INSTRUCTION MANUAL

AMPLIFICATEUR DE PUISSANCE 5 CANAUX

MODE D’EMPLOI

AMPLIFICADOR DE POTENCIA DE 5 CANALES

MANUAL DE INSTRUCCIONES

Main Page

Questions and Answers

N
Nicole RosalesJul 30, 2025
What to do if my Kenwood Amplifier has no sound?
- W
  wtaylorJul 30, 2025
  If your Kenwood Amplifier has no sound, it could be due to several reasons: * The input or output cables might be disconnected. Ensure they are properly connected. * The protection circuit may be activated. Check the connections according to the information about the protection function. * A blown fuse might be the cause. Replace the fuse, and consider lowering the volume. * A shorted speaker cord may also cause the issue. Inspect the speaker cord, fix any shorts, and then replace the fuse.
J
Joseph FletcherAug 14, 2025
Why does my Kenwood Amplifier sound distorted?
- K
  Kristin FletcherAug 14, 2025
  Distorted sound from your Kenwood Amplifier can stem from a few potential issues: * Incorrect speaker wire polarity (+/-). Ensure the speaker wires are correctly connected, paying close attention to the polarity of the terminals and wires. * A speaker wire pinched by a screw in the car body. Reconnect the speaker wire, making sure it's not pinched by anything. * Improper switch settings. Verify that all switches are correctly set, referring to the system examples for guidance.

Summary

Safety Precautions

General Safety Advice

Includes warnings and cautions regarding injury, fire, and equipment damage.

Unit Maintenance and Usage

Covers cleaning procedures and battery management advice.

Functional Safety Guidelines

Details protection functions, wiring, and speaker selection for safe operation.

Installation

Installation Procedure

Step-by-step instructions for mounting and connecting the amplifier.

Installation Location Precautions

Warnings and advice on selecting appropriate locations for amplifier installation.

Wiring and Connections

Power and Speaker Wire Setup

Instructions for connecting power, control, and speaker wires with safety notes.

Wiring Safety and Protection

Advice on preventing fire hazards and using protective fuses during wiring.

System Connections and Controls

RCA Cable Connections

Guide for connecting RCA cables between the center unit and the amplifier.

System Configuration Examples

Diagrams illustrating 5-channel and 3-channel system setups.

Amplifier Controls and Terminals

Identification and function of various controls and terminals on the amplifier.

Troubleshooting Guide

Audio Output Problems

Solutions for issues related to no sound or distorted audio output.

Level and Connection Issues

Troubleshooting steps for incorrect output levels and wiring problems.

Specifications

Audio Section Specifications

Detailed technical specifications for the amplifier's audio performance.

General Specifications

Overall specifications including operating voltage, consumption, dimensions, and weight.

Kenwood X700-5 Specifications

General

Channels	5
Signal-to-Noise Ratio	100 dB
THD at Rated RMS Power	0.08%
Low-Pass Crossover Frequency	50-200 Hz
High-Pass Crossover Frequency	50-200 Hz
Subwoofer Channel Crossover Frequency	50-200 Hz
Fuse Rating	40A
Crossover	Variable
RMS Power at 2 Ohms	75 watts x 4 + 500 watts x 1
Bass Boost	0-18 dB
Bass/Subsonic Filter	50 Hz
Input Sensitivity	0.2-5V
Bridged RMS Power (4 Ohms)	150W x 2 + 500W x 1