SELENA Multifunctional LED Clock USER MANUAL V32D
KERA TECHNOLOGIES INC. 2013 www.ledclocks.com
14
MONTH:YEAR display, followed by EXTERNAL TEMPERATURE display and all over again: HOURS:MINUTES display
followed by ... etc...etc...
NOTE, that the Real Time Clock mode (Fn 3), when alternating with other displays, always persists on the display the longest
(appx. 10 sec) while other displays will each remain on for shorter periods (appx 5 sec). This persistence split may be altered
by enabling the functions Fn 40 and / or Fn 41 .
If only one display mode is enabled, it will remain on the display all the time.
All three Time display Formats are available in all SELENA clocks.
The Function Fn 8 can be used to select between the
12 and 24 hour format
.
To select the
Military Time format
, enable the function Fn 45.
To select the display of
AM or PM
text indicator in the 6-digit clock, or in the Text display,
enable the functions Fn 8 and Fn 85.
HALTING the ALTERNATING DISPLAY in the Digital Time section
The user may (ON DEMAND) HALT the alternating display by pressing the HOLD key at any time. The screen currently on
the display will remain active until either a programming mode is initiated or the SCAN key is pressed.
Similarly, whenever the Timer/Counter START, STOP or RESET is performed externally or via the remote, the display will
switch to the timer/counter mode. Press the SCAN key to return to other display screens.
To scroll quickly through the enabled screens, press the SCAN key repeatedly.
NOTE: when the function Fn 62 is enabled, ALL COMMUNICATION with the clock via the remote control is DISABLED.
To regain the remote control access disconnect the power momentarily, then restore it and disable Fn 62 within 33 seconds.
Also see the function Fn 63 to disable the remote communication except the timer functions and the brightness control .
DATE / TEXT and ZONE Text display
( Optional Feature )
The TEXT option may be activated by enabling the function Fn 85.
In clocks with the optional Alpha Numeric text display installed, several modes for displaying of the current date and other text
modes may be selected by enabling the functions as per the table below:
Fn64 Fn65 Fn66
Mode “0” OFF OFF OFF * no date display
Mode “1” ON OFF OFF FRI-OCT-12
Mode “2” OFF ON OFF OCT-12-FRI
Mode “3” ON ON OFF 12-OCT-FRI
Mode “4” OFF OFF ON FRI-12-OCT
Mode “5” ON OFF ON 12-OCT-2007
Mode “6” OFF ON ON OCT-12-2007
Mode “7” ON ON ON 2007-12-OCT
* NOTE : If the Functions Fn 64, 65, 66 are set to 000, the Date will NOT be displayed. However other text modes may still be
activated and will display in an alternating manner if more than one is enabled.
Mode “8” Fn 72 HH-MM-SS-hh ( timer or counter ) ( also see Fn 35,38,39, )
Mode “9” Fn 73 Tmr MM-SS ( timer ) ( also see Fn 35,38,39, )
Mode “10” Fn 74 TIMER HH-MM ( timer or counter ) ( also see Fn 35,38,39, )
Mode “11” Fn 75 OUT 25 C ( or 77 F ) ( also see Fn 0 , Fn 1 and Fn 15 )
Mode “12” Fn 76 IN 25 C ( or 77 F ) ( also see Fn 0, Fn 1 and Fn 15 )
Mode “13” Fn 77 TEMP 25 C ( or 77 F ) ( also see Fn 0, Fn 1 and Fn 15, 27 )
Mode “14” Fn 78 DAY 245 ( Julian day of the year )
Mode “15” Fn 79 HH-MM-SS AM/PM ( real time clock ) ( also see Fn 8, 45, 84 )
Mode “16” Fn 80 TIME ZONE / Customer TEXT DISPLAY ( also see Fn 86 )
NOTE 1: In order to make any Text display alternate with other Text, enable more than one text display mode.
NOTE 2: The alternating text display is “halted” automatically if the FUN key is pressed or whenever any of the clock
programming modes is initiated. To resume the alternating text display after programming, press the TALK key.
To Next Page
Loading...