F4 Panpot: This modifies the arrangement of the timbre on the stereo panorama. The value can be changed using the
VALUE +/- push buttons which, if pressed together at the same time, take the timbre back to the middle of the
stereo panorama.
F5 Filter:
This calls up the page where some MIDI events can be cut-out from the reproduction of the track. It may occur
for example, that the musician wishes to avoid using the Modulation or some other MIDI parameter that direct-
ly affects the timbre. The MIDI filters can also be used to control an external MIDI module better. The page
called up from F5 Filter shows a table of four lines and four columns relative to the sixteen Parts. To be able
to access the MIDI filter of a single Part use the F1 and F6 push buttons for Parts 1, 2, 3 and 4 that are to be
selected by pressing the same push buttons repeatedly. Use push buttons F2 and F7 for Parts 5, 6, 7, and 8.
Use push buttons F3 and F8 for Parts 9, 10, 11 and 12 and push buttons F4 and F9 for Parts 13, 14, 15 and 16. Once
the Part to which the MIDI filter is to be applied has been found, select which MIDI message is to be cut-out from
the reproduction using the VALUE +/- push buttons and enable the filter using the F10 On/Off push button. The
filter is enabled when “ON” appears next the MIDI message to be filtered. The MIDI messages that can be fil-
tered are the following:
NNootteess::
all notes within the track
CCoonnttrrooll CChhaannggee::
all Control Changes within the track
PPrrooggrraamm CChhaannggee::
all Program Changes
AAfftteerr TToouucchh::
all After touch events
PPiittcchh BBeenndd::
all Pitch Bend events
VVoolluummee::
only Control Change 07 Volume
PPaann::
only Control Change 10 Pan
RReevveerrbb::
only Control Change XX Reverb Send
CChhoorruuss::
only Control Change XX Effect Send
MMoodduullaattiioonn WWhheeeell::
only Control Change 01 Modulation
EExxpprreessssiioonn::
only Control Change 11 Expression
RRPPNN::
only Control Change XX RPN
NNRRPPNN::
only Control Change XX NRPN
To exit from F5 Filter press EXIT that sends to the main page of Song Play.
F6 Key Shift: This changes the transposition of the track selected by up to +/- 24 semitones. The value can be changed using
the VALUE +/- push buttons which, if pressed together at the same time, reset the value.
F7 Channel Tx Rx: When push button F7 is pressed repeatedly it switches from TX, that indicates the transmission MIDI channel, to
RX, that establishes the MIDI receiving channel. The value can be changed using the VALUE +/- push buttons.
If no value is specified the track receives and transmits on the MIDI channel having the same number as the
Part.
F8 Part Mode: This modifies the operational mode of the track, using the VALUE +/- push buttons. The possible choices are:
Voice: track dedicated to the use of a timbre
Drumset: track dedicated to the use of a Drumset
Drum2: track dedicated to the use of Live Drumsets
Vocalize: track dedicated to the control of the Vocalizer
Based on the choice made Drumset, Live Drum, Voice and Vocal Set can be called up or otherwise. Whereas in
the case of Voice and Drumset mode the Voice and Drumset are called up normally. For Drum 2 and Vocal Set
the Live Drums and Vocal Sets must be selected using the VALUE +/- push buttons. The modification of opera-
tional mode of a track can make the song incompatible with modules in General MIDI, but it offers the best pos-
sible for creating Midi files on SD1.
F9 Mute: If the function is enabled (symbol √), the track is cut-out from the reproduction.
F10 16 Parts: This enables the display of each single parameter, showing its value for all sixteen Parts.
SD1 Owner’s Manual
106
To Next Page
Loading...
