3
PNA Series Network Analyzer
Option configurations
To add options to a product, order the corresponding item number.
Description For E8362C For E8363C For E8364C For E8361C Additional information
Test set
Option 014 Configurable test set E8362C-014 E8363C-014 E8364C-014 E8361C-014
Power configuration
Option UNL Extended power range
and bias-tees
E8362C-UNL E8363C-UNL E8364C-UNL E8361C-UNL Only E8361C requires 014
Option 016 Add receiver attenuators E8362C-016 E8363C-016 E8364C-016 E8361C-016 Requires UNL (only E8361C
also
requires 014)
Option H85
1
High-power
configuration
E8362CH85 E8363CH85 E8364CH85 Includes 014, 016, UNL
2
, 080,
081
Measurement applications
Option 010 Time-domain capability E8362C-010 E8363C-010 E8364C-010 E8361C-010
Option 080 Frequency offset E8362C-080 E8363C-080 E8364C-080 E8361C-080 Requires 014 (E8361C only,
081 required if UNL is also
purchased)
Option 081 Reference receiver
switch
E8362C-081 E8363C-081 E8364C-081
E8361C-081
Requires 014, 080 (only
E8361C also requires UNL)
Option 082 Scalar-calibrated con-
verter measurements
E8362C- 082 E8363 C -08 2 E83 64C -0 82 E8361C-082 Requires 014, 080
Option 083 Vector- and scalar-
calibrated converter
measurements
E8362C-083 E8363C-083 E8364C-083 E8361C-083 Requires 014, 080, 081(only
E8361C also
requires UNL)
Option 084
3
Embedded LO
measurements
E8362C-084 E8363C-084 E8364C-084 E8361C-084 Requires 082 or 083
Option 550
4
4-port measurement
application
E8362C-550 E836 3C -550 E8364C-550 E8361C-550 Requires 014
Option 551
4
N-port capabilities E8362C-551 E83 63C -551 E8364C-551 E8361C-551 Requires 014
Pulse, antenna, mm-wave
Option H08 Pulsed-RF measurement
capability
E8362C-H08 E8363C-H08 E8364C-H08 E8361C-H08 Requires 014, 080 (Option H11
recommended)
Option H11
IF access (for antenna,
pulsed-RF and mm-
wave measurements)
E8362C-H11 E8363C-H11 E8364C-H11 E8361C-H11 Requires 014, UNL, 080, and
081
Accessories
Option 1CM Rack mount kit for use
without handles
E8362C-1CM E8363C-1CM E836 4C-1CM E8361C-1CM
Option 1CP Rack mount kit for use
with handles
E8362C-1CP E8363C-1CP E8364C-1CP E8361C-1CP
Calibration documentation
Option 1A7 ISO 17025 compliant
calibration
E8362C-1A7 E8 363C-1A7 E8364C-1A7 E8361C-1A7
Option UK6 Commercial calibration
certificate with test data
E8362C-UK6 E8363C-UK6 E8364C-UK6 E8361C-UK6
Option A6J ANSI Z540 compliant
calibration
E8362C-A6J E8363C-A6J E8364C-A6J E8361C-A6J
Calibration software for self-maintainers
Option 897
5
Perpetual license of built-in
E8362C-897 E8363C-897 E8364C-897 E8361C-897
performance test software for Keysight exclusive calibration
Option 898
5
Perpetual license of built-in
E8362C-898 E8363C-898 E8364C-898 E8361C-898
performance test software for standards compliant calibration
1. Option H85 is ordered as a separate model, as indicated.
2. UNL up to 67 GHz does not include bias-tees. Only includes source attenuators.
3. Requires firmware A.07.05 and above, plus 1.1 GHz CPU board.
4. Option 550 is a subset of 551; therefore they cannot be ordered together. When ordering a test set, select an option to specify the appropriate
5. interconnect jumper cable set between the analyzer and the test set.
6. Additional hardware required. Please refer to the analyzer’s Service Guide for required service test equipment.
E8362C 10 MHz to 20 GHz E8363C 10 MHz to 40 GHz E8364C 10 MHz to 50 GHz E8361C 10 MHz to 67 GHz
To Next Page
Loading...
