Name: KLS Martin marLED E9i
Brand: KLS Martin
Rating: 4 (1 reviews)

To Next Page





Operating Lights marLEDOperating Lights marLED

®®

E9 / E9i / E15E9 / E9i / E15

Service ManualService Manual

V. V. 1.0-EN 1.0-EN (03.13) (03.13) Valid Valid for for marLEDmarLED

®®

E HW 00 and SW 00 or higherE HW 00 and SW 00 or higher

Default Chapter2
- Table of Contents2
- Warranty5
General Information General Information5
- User's Inspection5
  - Hotline6
    - Introduction Introduction7
Notice for Service Technicians7
Light Models7
Light Combinations8
Applicable Documents8
- KLS Martin Surgicam ® Digital , Surgicam HD8
Symbols Used in Symbols Used in this Service Manual this Service Manual8
Symbols Used on the Product9
Abbreviations9
- Safety Notices10
General Information10
- Circuit Diagrams13
Cable Colors13
- Light Engine Light Engine Wiring Wiring Diagram Diagram13
Circuit Diagram for Handle with Surgicam14
- Digital14
Tracking Arm Circuit Diagrams15
- Circuit Diagram Circuit Diagram for for 3-Pole Tracking Arm 3-Pole Tracking Arm with Backlite with Backlite Option Option15
  - Backlite Option16
- Ll Box with Optional Camera18
  - Ceiling Tube Wiring Diagrams Ceiling Tube Wiring Diagrams19
- Wiring Diagram for Rectifier for Ceiling Tube Max. 27 VAC / 26-36 VDC with ZSV Switch Switch19
Wiring Diagrams Power Wiring Diagrams Power Module SMPS Module SMPS 36/9 36/920
- Wiring Diagram Wiring Diagram Without Without ZSV ZSV Switch Switch20
- Wiring Diagram Wiring Diagram with with Integrated ZSV Integrated ZSV Switch Switch22
- Function of Function of the the Integrated ZSV Integrated ZSV Switch Switch (Optional (Optional) )23
- Voltage Voltage Adjustment23
  - Adjustment23
- Installation on Installation on a a Support Support Plate Plate24
- Mounting Rail Mounting Rail Installation24
  - Installation24
Cable Connection CAN and RS23225
- CAN Bus CAN Bus and and Addresse Addresses25
  - A a25
E9 / E9I / E1527
- Interface27
- Pin Pin Configur Configuration Ation X2 X2 (CAN, (CAN, RS232) RS232)28
  - Voltage Measurement Using the Service Plug29
Wiring Diagram for Operating Foil30
- Troubleshooting Troubleshooting31
Error Image with Error Image with Information on Information on Possible Causes and Possible Causes and Corrective Actions Corrective Actions31
- Replacement of Components Replacement of Components32
Setup of the Control Electronics with Microfuse33
- Display of the Display of the Operating Foil Operating Foil34
Components of the Lamp Body35
Removing the Light Engine Removing the Light Engine36
- Inserting the Light Engine Inserting the Light Engine37
Opening the Casing39
Replacing the Control Electronics40
Replacing the Operating Foil40
System Overview System Overview42
- Light Engine Light Engine Versions Versions43
  - Light Engine Pin Assignment Light Engine Pin Assignment43
Plug Connections on Plug Connections on Control Electronics and Light Control Electronics and Light Engine Engine44
- Light Engine Locations Light Engine Locations45
Plug Connections on Plug Connections on the Control the Control Electronics Electronics46
- Connections Ns for Connectio for Supply Supply Voltage Voltage and and Light Light Engines Engines49
Connection for D-Sub Plug50
Installation and Connection of Installation and Connection of the Additional Camera the Additional Camera Board Board51
- Configuration of the Marled53
- E Via E Via DIP Switch DIP Switch53
Interface Adapter Marled54
Software Update55
- Installing the Installing the C2Prog Programming Software C2Prog Programming Software on the on the PC PC55
- Connecting G the Connectin the Interface Interface Adapter Adapter55
- Programm Programming Ing56
- Replacing the Replacing the Cardan Suspension Cardan Suspension59
Closing the Casing63
- Change History Change History65
Overview of Software Changes65
Overview of Hardware Changes67
- Serial Number Structure68
- E9I / E1569
Technical Data Marled® E9 / E9I69
Technical Data Marled® E1570
Technical Safety Check Technical Safety Check and Intensive and Intensive Maintenance Maintenance72
Information Regarding the Technical Safety Check and Information Regarding the Technical Safety Check and Intensive Maintenance72
- Check74
Test Instructions for Test Instructions for Intensive Maintenance Intensive Maintenance76
Inspection Protocol-Technical Safety Inspection Protocol-Technical Safety Check Check90
Test Instructions for Safety Check (SC) Test Instructions for Safety Check (SC)91
Guidelines and Manufacturer's Declaration on Guidelines and Manufacturer's Declaration on Electromagnetic Electromagnetic Compatibility94
Spare Parts98
List of Tools98
List of Spare Parts98

Questions and Answers:

Need help?

Do you have a question about the KLS Martin marLED E9i and is the answer not in the manual?

KLS Martin marLED E9i Specifications

General

Brand	KLS Martin
Model	marLED E9i
Category	Medical Equipment
Language	English

Related product manuals

KLS Martin maxium Beamer

20 pages

KLS Martin maXium smart C

128 pages

KLS Martin ME102

44 pages

KLS Martin Minicutter

52 pages

KLS Martin LIMAX 120

86 pages

KLS Martin marLED E9i User Manual

Table of Contents

Questions and Answers:

KLS Martin marLED E9i Specifications

Related product manuals