How to fix thin, sandy, coarse finish/excessive overspray with Kobalt SGY-AIR176?
If your Kobalt Paint Sprayer is producing a thin, sandy, coarse finish or excessive overspray, try these solutions: * Move the gun closer to the surface. * Adjust the atomization pressure. * Move at a moderate pace, parallel to the surface, avoiding arcing motions.
What to do if Kobalt SGY-AIR176 will not spray?
If your Kobalt Paint Sprayer is not spraying, verify the following: * Check the air supply and air lines to ensure there is air pressure at the gun. * Open the fluid control screw and increase fluid pressure at the tank. * Thin the material if it is too heavy.
Why Kobalt Paint Sprayer has intermittent/sputtering spray?
If you're experiencing intermittent or sputtering spray with your Kobalt Paint Sprayer, consider the following: 1. Refill the material if the level is too low. 2. Hold the container more upright. 3. Tighten any loose fluid inlet connections. 4. Adjust or replace the needle seat if it is loose or damaged. 5. Lubricate or tighten the packing around the needle valve if it is dried out or loose. 6. Remove, clean, and tighten the fluid nozzle if it is loosely installed or if there is dirt between the nozzle and body. 7. Clean the vent hole if the air vent is clogged.
How to fix improper spray pattern with Kobalt SGY-AIR176?
If your Kobalt Paint Sprayer is producing an improper spray pattern, here are several possible solutions: * Reduce atomization air pressure if it is set too high. * Open the fluid adjustment knob if the material is too thin or the fluid adjustment pattern is turned in too far. * Partially close the pattern adjustment knob if the fan pattern is open too far.
Why is air pressure low on my Kobalt SGY-AIR176 Paint Sprayer?
If your Kobalt Paint Sprayer has low air pressure, adjust the regulator on the tool to the maximum setting and the compressor regulator to the tool maximum of 29 PSI. Keep in mind that air hoses may cause up to 15 PSI loss in pressure, so you might need to set a higher compressor output to maintain the required pressure at the tool.
What to do if my Kobalt SGY-AIR176 Paint Sprayer is dripping from fluid tip?
If your Kobalt Paint Sprayer is dripping from the fluid tip, try the following: * Lubricate if the packing is dry or the needle is sluggish. * Adjust if the packing nut is too tight. * Replace if the fluid nozzle or needle is worn.
Why is air leaking from air cap of my Kobalt SGY-AIR176?
To address air leaking from the air cap of your Kobalt Paint Sprayer without pulling the trigger: * Lubricate the air valve stem if it is sticking. * Clean any residue on the air valve or seat. * Replace any worn or damaged air valve or seat. * Replace the air valve spring if it is broken. * Replace the valve stem if it is bent.
How to prevent orange peel finish with Kobalt Paint Sprayer?
If your Kobalt Paint Sprayer is producing a thick, dimpled finish resembling orange peel, move the gun further from the surface.
Why Kobalt SGY-AIR176 Paint Sprayer unable to get round spray?
If you're unable to get a round spray pattern with your Kobalt Paint Sprayer, clean or replace the fan adjustment screw, in case it is not seating properly.
What causes fluid leakage from packing nut on Kobalt Paint Sprayer?
If you notice fluid leakage from the packing nut of your Kobalt Paint Sprayer, tighten the packing nut, but be careful not to restrict the needle. If the packing is worn or dry, replace it or lubricate it with non-silicone oil.
General| Max Pressure | 3000 PSI |
|---|---|
| Hose Length | 25 ft |
| Orifice Size | 0.015 in |
| Tip Size | 0.015 in |
| Voltage | 120 V |
| Type | Airless |
| Power Source | Electric |
To Next Page