Kohler 30RCL User Manual (English)

Other manuals for Kohler 30RCL

Questions and Answers:

R
Raymond MooreAug 18, 2025
How to troubleshoot a Kohler Inverter when it does not crank?
- K
  Kristina BellAug 18, 2025
  If your Kohler Inverter generator set does not crank, here are some things to check: * Recharge or replace the battery if it is weak or dead. * Check the battery connections to ensure they are properly connected. * Replace any blown fuses. If fuses blow repeatedly, contact an authorized Kohler distributor/dealer for service. * Ensure the generator set is turned ON by pressing the RUN button to start the engine or press AUTO to allow remote starting.
M
michaelbryantAug 20, 2025
Why does my Kohler Inverter have no AC output?
- S
  sarahhutchinsonAug 20, 2025
  If your Kohler Inverter has no AC output, make sure the AC circuit breaker is in the ON position. If the AC circuit breaker trips due to an overload, reduce the load on the generator set. If the breaker trips because of a short circuit, contact an authorized Kohler distributor/dealer for service.
R
Rachel FergusonAug 23, 2025
What to do if my Kohler Inverter generator cranks but doesn't start?
- J
  Jane NelsonAug 23, 2025
  If your Kohler Inverter generator set cranks but doesn't start, starts hard, lacks power, or operates erratically, here's what you can do: * Check and clean or replace the air cleaner if it's clogged. * Recharge or replace the battery if it's weak or dead. * Clean and tighten the battery connections if they are poor. * Inspect the spark plug wires for loose connections. * Look for oil leaks and check the oil level, adding oil if necessary, in case of a low oil pressure shutdown. * Check the fuel supply and valves if the fuel pressure is insufficient. If these steps don't resolve the issue, it might be an engine malfunction, and you should contact an authorized Kohler distributor/dealer.
A
Alison BradyAug 28, 2025
Why is there low output or excessive voltage drop on my Kohler Inverter?
- J
  jamie15Aug 28, 2025
  If you're experiencing low output or excessive voltage drop with your Kohler Inverter, it might be overloaded. Try reducing the load on the generator.
D
David JohnsonAug 30, 2025
What causes the controller LCD display to be off on a Kohler Inverter?
- R
  randy30Aug 30, 2025
  If the controller LCD display on your Kohler Inverter is off, check the connections and the generator set battery for low or no battery voltage. See Figure 5-1.
J
johnsonlauraSep 2, 2025
What to do when there is loss of communication to accessory modules in my Kohler Inverter?
- K
  Kimberly PhillipsSep 2, 2025
  If you are experiencing a loss of communication to accessory modules on your Kohler Inverter, check the wiring and connections. Also, verify that the cable size and length of run comply with the instructions in the Installation manual. You may also need to check the battery connections and the generator set battery for low or no battery voltage. See Figure 5-1.
S
Samuel HobbsSep 4, 2025
Why are the load management relays not operating on my Kohler Inverter?
- B
  benjaminwardSep 4, 2025
  If the load management relays on your Kohler Inverter do not operate, check the wiring and connections, ensuring that the cable size and length of run comply with the instructions in the Installation manual. Additionally, check the battery connections and the generator set battery for low or no battery voltage. See Figure 5-1.
C
Christina LambertSep 7, 2025
How to fix a flashing date on my Kohler Inverter?
- K
  kellybrianSep 7, 2025
  To address a flashing date on your Kohler Inverter, check the battery connections (see Figure 5-1) and the utility power connection for the built-in battery charger. Then, reset the time, date, and exercise schedule as described in Section 2.5.7, Setting the Exerciser at Power-Up.
R
Robert FieldsSep 9, 2025
Why are my Kohler Inverter fans operating in high-speed mode continuously?
- C
  Christopher LambertSep 10, 2025
  If the fans in your Kohler Inverter are constantly running at high speed, there might be an issue with airflow blockage in the radiator and enclosure openings. Inspect these areas to ensure they are clear. Also, check the sensor function, wiring harnesses from the fuse/relay terminal block to the fans and controller for any damaged leads or terminations. Evaluate the relays for proper functionality and check the coil continuity. Finally, verify the transition at the specified threshold temperatures.

Kohler 30RCL Specifications

General

Power Output	30 kW
Fuel Type	Gasoline, LPG, Natural Gas
Starting System	Electric Start
Power Rating (Gasoline)	30 kW
Power Rating (LPG)	27 kW
Voltage	120/240V
Frequency	60 Hz
Engine	Kohler