To Next PageTo Next PageWhat to do if Kohler Crankshaft operates erratically?
If your Kohler Crankshaft operates erratically, it is recommended to have a Kohler authorized dealer service or replace major engine components.
Why won't my Kohler Command PRO ECH749 Crankshaft engine crank?
If your Kohler Crankshaft engine won't crank, begin by ensuring the PTO drive is disengaged. A discharged battery is a common culprit; charge or replace it. Also, check if the safety interlock switch is engaged and disengage it. Loose or faulty wires or connections can prevent cranking; secure them. Other potential causes include a faulty key switch or ignition switch (replace if faulty), a faulty electric starter or solenoid (replace if faulty), or seized internal engine components (inspect and repair). A blown fuse, a faulty electronic control unit, or insufficient voltage to the electronic control unit can also prevent the engine from cranking; address these issues as necessary.
What causes a Kohler Crankshaft engine to lose power?
If your Kohler Crankshaft engine is losing power, several factors could be contributing. Begin by checking the crankcase oil level; refill if low or drain if high. A dirty air cleaner element can restrict airflow; clean or replace it. Also, dirt or water in the fuel system can cause power loss; check and replace the fuel if necessary. Excessive engine load can also cause this issue; reduce the load. Other potential causes include an overheated engine (ensure proper cooling), faulty spark plugs (replace them), low compression (perform a compression test and repair), an exhaust restriction (clear any restrictions), a low battery (charge or replace it), or an incorrect governor setting (adjust the setting).
What should I do if my Kohler Crankshaft engine overheats?
If your Kohler Crankshaft engine is overheating, several factors could be the cause. Start by checking for clogged air intake/grass screens, cooling fins, oil cooler, or cooling shrouds; clean these components to ensure proper airflow. Excessive engine load can also cause overheating; reduce the load. Check the crankcase oil level; refill if low or drain if high. A lean air-fuel mixture can also contribute to overheating; adjust the air-fuel mixture to the proper levels.
Why does my Kohler Crankshaft engine run but miss?
If your Kohler Crankshaft engine runs but misses, several factors could be responsible. Start by checking for dirt or water in the fuel system; check and replace the fuel as necessary. Ensure the spark plug lead is connected. Poor fuel quality can also cause missing; use proper fuel quality. Other potential causes include faulty spark plugs (replace them), loose wires or connections (secure them), an overheated engine (ensure proper cooling), a faulty ignition module (replace it), an incorrect crankshaft position sensor air gap (adjust it), or insufficient voltage to the electronic control unit (ensure proper voltage supply).
What causes a Kohler Command PRO ECH749 Crankshaft engine to knock?
If your Kohler Crankshaft engine is knocking, several factors could be the cause. Excessive engine load can cause knocking; reduce the load. Check the crankcase oil level; refill if low. Old or improper fuel can also cause knocking; use fresh and appropriate fuel. Other potential causes include internal wear or damage (inspect and repair internal engine components), hydraulic lifter malfunction (repair or replace), improper fuel quality (use proper fuel quality), or an incorrect grade of oil (use the correct grade of oil).
Why won't my Kohler Command PRO ECH749 engine idle properly?
If your Kohler Crankshaft engine will not idle, several factors could be responsible. Start by checking for dirt or water in the fuel system; check and replace the fuel as necessary. Stale fuel or dirty fuel injectors can also cause idling issues; replace stale fuel or clean the fuel injectors. Other potential causes include faulty spark plugs (replace them), an inadequate fuel supply (ensure adequate fuel supply), low compression (perform a compression test and repair), a restricted fuel tank cap vent (clear the vent), or an overheated engine due to cooling system or air circulation problems (ensure proper cooling and air circulation).
What causes a Kohler Command PRO ECH749 engine to use excessive oil?
If your Kohler Crankshaft engine uses an excessive amount of oil, several factors could be contributing. First, check if you're using the incorrect oil viscosity or type and use the correct one. A clogged or improperly assembled breather can cause excessive oil consumption; clear or correctly assemble the breather. Other potential causes include a broken breather reed (replace it), worn or broken piston rings (replace them), a worn cylinder bore (repair or replace it), worn valve stems or valve guides (replace them), a crankcase overfilled (drain excess oil), or a blown head gasket or overheating (replace the head gasket).
Why is my Kohler Command PRO ECH749 engine leaking oil from the seals and gaskets?
If your Kohler Crankshaft engine is leaking oil from the oil seals or gaskets, several factors could be the cause. A clogged or inoperative crankcase breather can cause oil leaks; clear or repair the breather. A broken breather reed can also cause leaks; replace the breather reed. Loose or improperly torqued fasteners can cause leaks; tighten fasteners to the correct torque specifications. Piston blowby or leaky valves can also cause this issue; repair or replace the piston or valves. Finally, a restricted exhaust can contribute to oil leaks; clear any exhaust restrictions.
What to do if Kohler Crankshaft lacks power?
If your Kohler Crankshaft lacks power, it is recommended to have a Kohler authorized dealer service or replace major engine components.
General| Fuel System | Carburetor |
|---|---|
| Starter | Electric |
| Governor Type | Mechanical |
| Lubrication System | Full Pressure |
| Fuel Type | Gasoline |
| Crankshaft Orientation | Horizontal |
| Bore | 3.27 in (83 mm) |
| Cooling System | Air |
| Oil Type | SAE 10W-30 |
| Spark Plug Gap | 0.030 in (0.76 mm) |
| Valve Clearance - Intake | 0.004 - 0.006 in (0.10 - 0.15 mm) |
| Crankshaft Type | Varies by model |
| Crankshaft Thread Size | Varies by model |
| Crankshaft Length | Varies by model |
| Crankshaft Diameter | Varies by model |
| Type | Overhead Valve (OHV) |
