EasyManuals Logo

Kohler Command PRO ECH749 User Manual

Kohler Command PRO ECH749
8 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #5 background imageLoading...
Page #5 background image
5
24 590 28 Rev. --
KohlerEngines.com
Maintenance Instructions
WARNING
Before working on engine or equipment, disable
engine as follows: 1) Disconnect spark plug
lead(s). 2) Disconnect negative (–) battery cable
from battery.
Accidental Starts can cause
severe injury or death.
Disconnect and ground spark
plug lead(s) before servicing.
Normal maintenance, replacement or repair of emission control devices and systems may be
performed by any repair establishment or individual; however, warranty repairs must be performed
by a Kohler authorized dealer found at KohlerEngines.com or 1-800-544-2444 (U.S. and Canada).
Oil Recommendations
We recommend use of Kohler oils for best
performance. Other high-quality detergent
oils (including synthetic) of API (American
Petroleum Institute) service class SJ or higher
are acceptable. Select viscosity based on air
temperature at time of operation as shown in
table below.
°F
-20
020324060
50 80 100
°C
-30 -20
-10 0
10 20 30
40
5W-30
10W-30
SAE 30
Check Oil Level
NOTE: To prevent extensive engine wear or
damage, never run engine with oil level
below or above operating range
indicator on dipstick.
Ensure engine is cool. Clean oil ll/dipstick
areas of any debris.
1. Remove dipstick; wipe oil off.
a. Push-on cap: reinsert dipstick into tube;
press completely down.
or
b. Threaded cap: reinsert dipstick into
tube; rest cap on tube, do not thread cap
onto tube.
2. Remove dipstick; check oil level. Level
should be at top of indicator on dipstick.
3. If oil is low on indicator, add oil up to top of
indicator mark.
4. Reinstall and secure dipstick.
Maintenance Schedule
Every 25 Hours or Annually¹
Service/replace low-pro le precleaner (if equipped).
Every 100 Hours or Annually¹
Change oil.
Replace low-pro le air cleaner element.
Remove and clean shrouds and cooling areas.
Check oil cooler ns, clean as necessary (if equipped).
Every 150 Hours
Check heavy-duty lter minder.
Inspect heavy-duty air lter paper element and inlet screen area.
Every 200 Hours¹
Replace unique Electronic Fuel Injection (EFI) fuel lter.
Every 200 Hours
Change oil lter.
Replace spark plugs and set gap.
Every 300 Hours¹
Replace heavy-duty air cleaner element and check inner element.
Every 600 Hours¹
Replace heavy-duty air cleaner inner element.
1
Perform these procedures more frequently under severe, dusty, dirty conditions.

Other manuals for Kohler Command PRO ECH749

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Kohler Command PRO ECH749 and is the answer not in the manual?

Kohler Command PRO ECH749 Specifications

General IconGeneral
Fuel SystemCarburetor
StarterElectric
Governor TypeMechanical
Lubrication SystemFull Pressure
Fuel TypeGasoline
Crankshaft OrientationHorizontal
Bore3.27 in (83 mm)
Cooling SystemAir
Oil TypeSAE 10W-30
Spark Plug Gap0.030 in (0.76 mm)
Valve Clearance - Intake0.004 - 0.006 in (0.10 - 0.15 mm)
Crankshaft TypeVaries by model
Crankshaft Thread SizeVaries by model
Crankshaft LengthVaries by model
Crankshaft DiameterVaries by model
TypeOverhead Valve (OHV)

Related product manuals