Need help?Do you have a question about the Kongsberg EM 2040P and is the answer not in the manual?
General| Brand | Kongsberg |
|---|---|
| Model | EM 2040P |
| Category | Marine Equipment |
| Language | English |
Defines the purpose and target audience of the installation manual for the EM 2040P.
Provides guidance on following manual procedures for optimal performance and system setup.
Summarizes the main features and capabilities of the EM 2040P multibeam echo sounder.
Illustrates the main components and connections of a basic EM 2040P system.
Details the EM 2040P transducer, its configuration, and materials.
Describes the central controlling device of the EM multibeam system.
Explains the portable version of the EM 2040P Processing Unit.
Details the operator station for the EM 2040P system.
Describes the junction box for remote control and synchronization of echo sounders.
Specifies the required skills and certifications for installation personnel.
Outlines the necessary environmental, electrical, and physical requirements for the sonar room.
Provides guidelines and recommendations for optimal transducer placement on the hull.
Discusses sources of acoustic noise and their impact on system performance.
Explains the importance and setup of the vessel's coordinate system for sensor data.
Provides essential rules for safely handling the transducer to prevent damage.
Outlines the procedure and prerequisites for transducer installation.
Discusses principles for permanent and non-permanent transducer installations.
Details the procedure and requirements for painting the transducer face.
Lists approved anti-fouling paints for transducer protection.
Provides step-by-step instructions for installing the EM 2040P Processing Unit.
Details the installation of the portable version of the EM 2040P Processing Unit.
Guides the installation of the Hydrographic Work Station computer.
Provides essential information and warnings regarding cable specifications and installation.
Illustrates the cable connections for the Processing Unit in a single swath configuration.
Illustrates the cable connections for the Processing Unit in a dual swath configuration.
Shows the cable connections for the Portable Processing Unit.
Depicts the cable layout for the topside equipment, including the display and keyboard.
Provides a comprehensive list of all cables required for the EM 2040P system.
Details the RS-232 serial line connection using three wires and an RJ45 connector.
Details the RS-422 serial line connection using five wires and an RJ45 connector.
Explains the clock synchronization using a coax cable for the 1PPS signal.
Provides specifications and diagrams for transducer cables.
Describes the cable connecting the Portable Processing Unit to a Seapath 130 antenna.
Details the cable for connecting the Portable Processing Unit to a Seapath antenna.
Describes the cable connecting the Portable Processing Unit to a Seapath Motion Reference Unit.
Details the cable used to connect the Portable Processing Unit to a DC power supply.
Provides detailed dimensional drawings of the EM 2040P transducer.
Shows the dimensions of the Processing Unit for rack or cabinet installation.
Provides dimensional drawings for the Portable Processing Unit.
Details the dimensions of the Hydrographic Work Station computer.
Shows the dimensional data for the Remote Control Unit (K-REM).
Illustrates the wiring diagram for the Remote Control Unit (K-REM).
Summarizes the functional and operational characteristics, including frequency, depth, and coverage.
Details supported datagram formats for position, clock, heading, motion, and depth information.
Lists the physical dimensions and weights of the system components.
Specifies the voltage and power consumption requirements for each system unit.
Outlines the operational and storage temperature, humidity, and protection ratings.
Defines the accuracy requirements for transducer, motion, heading, and position sensor alignment.
Provides guidelines for transporting Kongsberg Maritime electronic, electromechanical, and mechanical units.
Details safe procedures for lifting heavy equipment units and their packaging.
Describes the process for visually inspecting units and boxes upon arrival.
Outlines general specifications for storing equipment before it is installed or used.
Provides basic procedures for unpacking main units and spare parts.
Details the process for unpacking mechanical units, emphasizing safe handling.
Explains how to unpack electronic and electromechanical units, including ESD precautions.
Provides instructions for safely unpacking transducers, sonar heads, and hydrophones.
Emphasizes switching off power, using warning signs, and having personnel present for safety.
To Next Page
