Why is my Konica Minolta Measuring Instruments reading automatically?
If your Konica Minolta Measuring Instruments DR detector is automatically starting to read images, it may be due to strong shocks or vibrations while in "Ready" status, or nearby X-ray exposure. To resolve this: * Avoid strong shocks or vibrations. * Restart the exposure process.
How to troubleshoot a Konica Minolta AeroDR SKR 4000 Measuring Instruments DR Detector that does not start?
If your Konica Minolta Measuring Instruments DR Detector isn't starting up, it could be due to a few reasons. First, ensure the battery is correctly inserted and fully charged. If the problem continues, the battery's output may be locked; charge it for over 30 seconds using the battery charger to unlock it. Alternatively, if you're using the DC power cable, ensure it's correctly connected.
What to do if no image is acquired on Konica Minolta AeroDR SKR 4000?
If no image is acquired after X-ray exposure with your Konica Minolta Measuring Instruments, check the following: * Confirm that the exposure was performed in "Ready" status. * Verify that the exposure conditions are correct. * Check if the X-ray output was lowered or the X-ray voltage was set too low. If these are correct, try increasing the voltage of the X-ray before exposure.
What does it mean when the charging LED (orange) and fully charged LED (green) are flashing fast on Konica Minolta Measuring Instruments?
If the charging LED (orange) and fully charged LED (green) are flashing rapidly on your Konica Minolta Measuring Instruments, a system error might be occurring. If a battery is inserted, remove it. Disconnect and then reconnect the AC power cable from the wall outlet, and then restart the battery charger.
What to do if the status LED (green) does not light on Konica Minolta AeroDR SKR 4000 Measuring Instruments?
If the status LED (green) on your Konica Minolta Measuring Instruments does not light up, it indicates a system error. If the status LED (green) doesn't turn on after approximately 10 minutes, try restarting the DR detector. Alternatively, if "Ready" isn't displayed on the image processing controller, restart the controller.
Why does the battery LED turn orange too fast on Konica Minolta Measuring Instruments?
If the battery LED on your Konica Minolta Measuring Instruments is turning orange too quickly, it could indicate that the battery's charging function has deteriorated. In this case, replace the battery.
What to do if Konica Minolta Measuring Instruments DR Detector does not shut down?
If the Konica Minolta Measuring Instruments DR Detector does not shut down, it is because it is not possible to shut down while exposing. Shut down after exposure is ended.
Why is my Konica Minolta AeroDR SKR 4000 not charging when the battery is inserted?
If your Konica Minolta Measuring Instruments is not charging when the battery is inserted, ensure that the battery is correctly inserted into the charger.
What does it mean when the status LED (orange) is flashing on Konica Minolta AeroDR SKR 4000?
If the status LED (orange) is flashing on your Konica Minolta Measuring Instruments, it indicates a system error. Restart the DR detector to resolve this issue.
Why is the power LED (green) not lighting on my Konica Minolta Measuring Instruments?
If the power LED (green) on your Konica Minolta Measuring Instruments isn't lighting up, it's likely that AC power isn't being supplied. Ensure that the power cable is correctly connected to the device.
General| Type | Digital Radiography System |
|---|---|
| Pixel Pitch | 150 μm |
| Spatial Resolution | 3.3 lp/mm |
| Technology | Flat Panel Detector |
| Detector Type | CsI Scintillator |
| Detector Size | 17 x 17 inches |
| A/D Conversion | 16 bits |
| Data Output | Gigabit Ethernet |
| Interface | Gigabit Ethernet |
| Operating Temperature | 10°C to 40°C (50°F to 104°F) |
| Operating Humidity | 30% to 75% (non-condensing) |
To Next Page