What to do if my KTM Motorcycle engine turns but does not start?
If your KTM Motorcycle engine turns but doesn't start, one potential cause is that the plug-in connection of the fuel hose is not connected; connect it. Another cause could be a fault in the fuel injection system, which requires using the KTM diagnostics tool to read out the fault memory. The fuel quality could also be insufficient, so add suitable fuel.
What to do if the engine does not turn when pressing the emergency OFF switch/electric starter button on my KTM Motorcycle?
If the engine of your KTM Motorcycle doesn't turn when the emergency OFF switch/electric starter button is pressed into the lower position, it's likely an operating error. Make sure to correctly carry out the start procedure.
What to do if there is no response when pressing the Race?on tip switch on my KTM 1290 SUPER ADVENTURE R 2018 Motorcycle?
If there is no response when the Race?on tip switch is pressed on your KTM Motorcycle, the Race?on tip switch may be faulty. Check the Race?on tip switch for damage and inspect the cable and plug of the Race?on tip switch for any damage.
What to do if my KTM Motorcycle engine dies during the trip?
If your KTM Motorcycle engine dies during a trip, it could be due to a lack of fuel. In this case, refuel your motorcycle. Another possible cause is a fault in the fuel injection system, which requires reading out the fault memory using the KTM diagnostics tool.
Why does my KTM 1290 SUPER ADVENTURE R 2018 Motorcycle have high oil consumption?
High oil consumption in your KTM Motorcycle can be caused by a couple of things. First, check if the engine oil level is too high. Second, the engine oil might be too thin (low viscosity). If that's the case, change the engine oil and oil filter, and also clean the oil screens.
Why is the battery discharged on my KTM Motorcycle?
A discharged battery in your KTM Motorcycle could be due to several reasons. It might be that a power consumer is connected to the socket/ACC1, so disconnect it. Another reason could be that the hazard warning flasher is switched on, so switch it off. Also, the battery might not be charged by the alternator, so check the charging voltage. Finally, the ignition may not have been switched off when the vehicle was parked, so recharge the battery.
Why does the combination instrument show nothing on the display of my KTM 1290 SUPER ADVENTURE R 2018 Motorcycle?
If the combination instrument on your KTM Motorcycle display is blank, it could be due to a few reasons. First, check if Fuse 1 is blown and change the fuses in the fuse box if needed. Another possibility is that the main fuse burned out, so replace the main fuse. Lastly, the battery could be discharged, so recharge the battery and check the open-circuit current.
Why does the ABS indicator lamp light up on my KTM 1290 SUPER ADVENTURE R 2018 Motorcycle?
If the ABS indicator lamp lights up on your KTM Motorcycle, there are several potential causes. The ABS fuse might be blown, so change the fuses in the fuse box. The wheel speeds of the front and rear wheels may differ greatly, so stop, switch off the ignition, and start again. It could also indicate a malfunction in the ABS, requiring you to read out the fault memory using the KTM diagnostics tool.
What does it mean if the malfunction indicator lamp lights up on my KTM 1290 SUPER ADVENTURE R 2018?
If the malfunction indicator lamp lights up on your KTM Motorcycle, it indicates a fault in the fuel injection system. To address this, read out the fault memory using the KTM diagnostics tool.
What does it mean if the Race?on indicator lamp flashes twice on my KTM 1290 SUPER ADVENTURE R 2018?
If the Race?on indicator lamp flashes twice on your KTM Motorcycle, it suggests there's no response signal from the Race?on key. To resolve this, ensure the Race-on key is in range, remove other electronic devices from the vicinity of the Race-on antenna, check the battery compartment in the Race?on key for correct locking, check the battery holder of the Race?on key for corrosion. You can also try changing the Race-on key battery or using the black ignition key.
General| Engine Type | 2-cylinder, 4-stroke, V 75° |
|---|---|
| Displacement | 1301 cc |
| Torque | 140 Nm |
| Bore x Stroke | 108 mm x 71 mm |
| Transmission | 6-speed |
| Fuel System | Electronic fuel injection |
| Cooling | Liquid cooled |
| Front Suspension | WP USD Ø 48 mm |
| Fuel Tank Capacity | 23 liters |
| Seat Height | 890 mm |
| Weight | 217 kg (dry) |
| Power | 160 hp |
| Rear Suspension | WP monoshock |
| Front Brake | 2 x 320 mm discs, 4-piston radial fixed caliper |
| Rear Brake | 267 mm disc, 2-piston caliper |
| Traction Control | Motorcycle Traction Control (MTC), disengageable |
| Wheelbase | 1580 mm |
Clarifies the meaning of various risk levels and symbols used to indicate potential dangers.
Provides essential instructions and warnings for operating the motorcycle safely.
Explains the function and operation of the motorcycle's clutch lever.
Details the function of the emergency OFF and electric starter button for engine operation.
Explains the meaning and function of various indicator lamps on the instrument cluster.
Describes warning notes that appear on the display indicating errors or required actions.
Details the Antilock Braking System, its modes, and operational information.
Offers essential advice and safety precautions before the motorcycle's initial use.
Provides guidelines for the engine break-in period to ensure optimal performance and longevity.
Explains how to properly load the vehicle, considering weight limits and handling characteristics.
Lists critical checks and maintenance tasks to perform before every ride.
Details the procedure for safely starting the motorcycle's engine.
Provides instructions and warnings on the correct application of the motorcycle's braking system.
Explains the correct procedures for stopping, parking, and securing the motorcycle.
Explains the functionality, modes, and safety aspects of the ABS system.
Provides safety precautions and steps for removing the motorcycle battery.
Details the procedure for locating and replacing the main fuse.
Explains how to select and use different ride modes for engine and traction control tuning.
Provides instructions on how to check the engine oil level correctly.
Step-by-step guide for changing engine oil, oil filter, and cleaning oil screens.
To Next Page