What to do if the engine turns but does not start on my KTM 1290 Super Duke R AU 2015 Motorcycle?
If the engine turns but does not start on your KTM Motorcycle, it could be due to a defect in the fuel injection system. Another possible reason is that the fuel quality is insufficient, so add suitable fuel.
What to do if the combination instrument shows nothing on the display on my KTM Motorcycle?
If the combination instrument on your KTM Motorcycle shows nothing on the display, several factors could be at play. It might be due to a blown Fuse 1, in which case you should change the fuses in the fuse box. Alternatively, the main fuse could be blown, requiring you to change the main fuse. A discharged battery could also be the culprit, so recharge the battery and check the open-circuit current. Lastly, a faulty ignition/steering lock could be the reason, so inspect the ignition/steering lock.
Why does my KTM Motorcycle engine die during the trip?
If your KTM Motorcycle engine dies during a trip, it could be due to a lack of fuel, so refuel your motorcycle. Another potential cause is a defect in the fuel injection system.
What does it mean if the ABS warning lamp lights up on my KTM 1290 Super Duke R AU 2015?
If the ABS warning lamp lights up on your KTM Motorcycle, it could be due to a blown ABS fuse, so change the fuses in the fuse box. It could also be due to a large difference in wheel speeds of the front and rear wheels, in this case, stop the vehicle, switch off the ignition, and start it again. Another potential cause is a malfunction in the ABS.
What to do if the engine does not crank when the electric starter button is pressed on my KTM 1290 Super Duke R AU 2015?
If the engine does not crank when you press the electric starter button on your KTM Motorcycle, first ensure that the emergency OFF switch is in the ON position. Another cause may be an operating error; make sure you carry out the start procedure correctly. A discharged battery could also be the issue, so recharge the battery and check the open-circuit current. Other potential causes include a faulty safety start system, a CAN bus communication error, a fault in the EFI control unit, or a fault in the MCU control unit.
Why is there a high oil consumption in my KTM 1290 Super Duke R AU 2015?
High oil consumption in your KTM Motorcycle can stem from a couple of issues. First, check if the engine oil level is too high. Also, the engine oil might be too thin (low viscosity), in that case change the engine oil and filter, and clean the oil screens.
Why is the battery discharged on my KTM Motorcycle?
If your KTM Motorcycle battery is discharged, it might be because the hazard warning flasher is switched on, so switch off the hazard warning flasher and recharge the battery. Another possible reason is that the battery is not being charged by the alternator, so check the charging voltage. Also, the ignition might not have been switched off while the vehicle was parked, so recharge the battery.
What does it mean if the engine warning lamp lights up/flashes on my KTM 1290 Super Duke R AU 2015?
If the engine warning lamp lights up or flashes on your KTM Motorcycle, it could be due to a defect in the fuel injection system.
Why does the engine only turn if the clutch lever is drawn on my KTM Motorcycle?
If the engine only turns when the clutch lever is drawn on your KTM Motorcycle, it could be that the vehicle is in gear, so shift the transmission to idle. Another potential cause is a faulty safety start system.
General| Brand | KTM |
|---|---|
| Model | 1290 Super Duke R AU 2015 |
| Category | Motorcycle |
| Language | English |
Explains the meaning of specific symbols used in the manual.
Explains the typographical formats used in the document.
Defines the intended use of the KTM sport motorcycles.
Provides essential safety instructions for operating the vehicle.
Explains danger levels and associated warning symbols.
Warns against tampering with the noise control system.
Details crucial guidelines for safe operation of the motorcycle.
Emphasizes the importance of wearing appropriate protective gear.
Outlines rules for work and environmental considerations.
Stresses the importance of reading and keeping the owner's manual.
Details conditions and procedures for guarantee and warranty claims.
Covers safe use and environmental impact of fluids and lubricants.
Guides on using approved spare parts and accessories.
Explains the importance of proper service for optimal operation.
Provides information on manual figures and customer support.
Labels key components from the front left view of the vehicle.
Labels key components from the rear right view of the vehicle.
Explains where to find chassis and type label numbers.
Details the key number and its importance for spare keys.
Locates the engine number and fork part number.
Identifies part numbers for shock absorber and steering damper.
Operation of clutch, brake levers, throttle, and handlebar switches.
Details ignition lock, immobilizer, filler cap, and seat lock.
Covers passenger footrests, baggage lugs, tool set, and foot controls.
Describes the instrument overview and activation process.
Explains matrix/segment displays, indicators, and warning messages.
Covers menu options like Favorites, Settings, Language, and Modes.
Adjusting handlebar position and lever basic settings.
Adjusting shift lever and foot brake lever step plate.
Provides advice for first use and engine running-in procedures.
Covers vehicle loading guidelines and pre-ride maintenance checks.
Details pre-ride checks and starting the motorcycle.
Covers shifting, riding techniques, and applying brakes.
Provides instructions for stopping, parking, and transporting the vehicle.
Guides on safe and proper refueling of the motorcycle.
Outlines scheduled maintenance tasks and intervals for the vehicle.
Adjusting compression and rebound damping on the fork.
Adjusting compression, rebound damping, and spring preload.
Procedures for using front and rear lifting gears safely.
Silencer removal, chain checks, tension, and sprocket inspection.
Procedure for checking and correcting the hydraulic clutch fluid level.
Details on the ABS system and its limitations.
Procedures for checking brake disc wear and brake lining thickness.
Procedures for checking and adding front and rear brake fluid.
Procedures for removing and installing front and rear wheels.
Checking tire wear, tread depth, and air pressure.
Procedures for removing, installing, and recharging the battery.
Changing main and individual fuses in the fuse box.
Changing headlight bulbs, adjusting range, and key activation.
Procedures for checking and topping up coolant levels.
Selecting drive modes and managing MTC.
Procedures for checking engine oil level and changing oil/filter.
Instructions for adding engine oil to the correct level.
Guidelines for cleaning the motorcycle safely and effectively.
Checks and maintenance steps for operating in winter conditions.
Steps for storing and preparing the motorcycle after storage.
Lists common problems with their possible causes and actions.
Details engine design, displacement, and chassis dimensions.
Lists engine and chassis tightening torques and fluid capacities.
Provides specifications for electrical, tire, fork, and shock absorber systems.
Details on brake fluid, coolant, engine oil, and fuel grades.
Lists recommended suppliers for chain cleaner, lube, polish, etc.
Explains JASO T903 MA and SAE viscosity standards for oils.
To Next Page
