What to do if the KTM 2014 1290 Super Duke R FR engine turns but does not start?
If your KTM Motorcycle engine turns but doesn't start, consider these potential causes: * There may be a defect in the fuel injection system. In this case, read out the fault memory using the KTM diagnostics tool. * The fuel quality might be insufficient. Try adding suitable fuel.
Why is the oil consumption high in my KTM Motorcycle?
High oil consumption in your KTM Motorcycle could be due to several reasons: * The engine oil level may be too high, so check the engine oil level. * The engine oil might be too thin (low viscosity). If so, change the engine oil and filter, and clean the oil screens.
What to do if the KTM 2014 1290 Super Duke R FR engine does not crank when pressing the electric starter button?
If your KTM Motorcycle engine fails to crank when you press the electric starter button, there are a couple of things you can check: * Ensure the emergency OFF switch is in the ON position. * Make sure you are following the correct start procedure.
Why does the engine die during a KTM Motorcycle trip?
The engine of your KTM Motorcycle might die during a trip due to a lack of fuel. Refuel your vehicle to solve this problem.
What does it mean if the ABS warning lamp lights up on my KTM 2014 1290 Super Duke R FR?
If the ABS warning lamp lights up on your KTM Motorcycle, it could indicate a couple of issues: * The ABS fuse may be blown. If this is the case, change the fuses in the fuse box. * There might be a large difference in wheel speeds between the front and rear wheels. Try stopping the vehicle, switching off the ignition, and starting it again.
What does it mean if the engine warning lamp lights up or flashes on a KTM 2014 1290 Super Duke R FR?
If the engine warning lamp lights up or flashes on your KTM Motorcycle, it indicates a defect in the fuel injection system. Read out the fault memory using the KTM diagnostics tool.
What to do if the combination instrument shows nothing on the display of my KTM Motorcycle?
If the combination instrument on your KTM Motorcycle shows nothing on the display, check the following: * Fuse 1 might be blown. Change the fuses in the fuse box. * The main fuse could be blown. Replace the main fuse. * The battery may be discharged. Recharge the battery.
General| Displacement | 1301 cc |
|---|---|
| Bore x Stroke | 108 mm x 71 mm |
| Compression Ratio | 13.2:1 |
| Fuel System | Electronic fuel injection |
| Starter | Electric |
| Lubrication | Forced oil lubrication with 3 oil pumps |
| Transmission | 6-speed |
| Dry Weight | 189 kg |
| Engine Type | V-twin, four-stroke |
| Power | 180 hp (132 kW) @ 8870 rpm |
| Torque | 144 Nm @ 6, 500 rpm |
| Clutch | PASC slipper clutch |
| Frame | Steel trellis frame |
| Front Suspension | WP USD 48 mm |
| Rear Suspension | WP monoshock |
| Front Brake | Dual 320 mm discs, Brembo 4-piston calipers |
| Rear Brake | Single 240 mm disc, Brembo 2-piston caliper |
| ABS | Bosch 9ME combined ABS (switchable) |
| Wheelbase | 1482 mm |
| Seat Height | 835 mm |
| Fuel Capacity | 18 liters |
Provides essential safety instructions for operating the vehicle.
Provides guidelines for safe operation of the motorcycle.
Emphasizes the importance of wearing protective clothing.
Describes the clutch lever and its hydraulic operation.
Explains the hand brake lever and its function for the front brake.
Describes the function of the emergency OFF switch.
Explains the operation of the electric starter button.
Details the ignition lock and steering lock mechanism.
Details the foot brake lever for the rear brake.
Details the matrix display and its functions.
Lists and explains the meaning of various indicator lamps.
Provides crucial advice and warnings for the first use of the motorcycle.
Details the engine break-in phase and recommended speed limits.
Lists essential checks and maintenance measures before riding.
Provides a step-by-step guide for starting the motorcycle engine.
Explains the procedure for starting off from a standstill.
Guides on shifting gears, riding, and adapting to conditions.
Details proper braking techniques and warnings.
Details the procedure for refueling the motorcycle safely.
Lists maintenance tasks required at specific intervals.
Explains how to adjust the compression damping of the front fork.
Guides on adjusting the rebound damping of the front fork.
Provides steps for adjusting the low-speed compression damping of the shock absorber.
Details how to adjust the high-speed compression damping of the shock absorber.
Explains how to adjust the rebound damping of the shock absorber.
Guides on adjusting the spring preload of the shock absorber.
Explains how to check and adjust the chain tension.
Explains the ABS system, its modes, and potential malfunctions.
Details how to check brake disc thickness and for damage.
Guides on checking and adding front brake fluid.
Explains how to check the minimum thickness and condition of front brake linings.
Details how to check the minimum thickness and condition of rear brake linings.
Step-by-step guide for removing and installing the front wheel.
Procedure for removing and installing the rear wheel.
Explains how to check and correct tire air pressure.
Details the procedure for activating and deactivating ignition keys.
Explains the 'Drive Mod' settings (Sport, Street, Rain).
Describes the motorcycle traction control system and its settings.
Provides instructions for checking the engine oil level.
Details the procedure for changing engine oil, filter, and cleaning oil screens.
Lists common faults with the combination instrument and their solutions.
Troubleshoots issues related to the engine not starting or cranking.
Addresses engine issues like dying during trips or warning lamps.
Lists torque specifications for various engine screws and bolts.
Lists torque specifications for various chassis screws and bolts.
To Next Page