What to do if my KTM Motorcycle engine turns but does not start?
If your KTM Motorcycle engine turns but doesn't start, a possible cause is that the quick release coupling is not joined, so join it. Another cause may be a malfunction in the electronic fuel injection and in this case you should read out the fault memory using the KTM diagnostics tool. Finally, the fuel quality might be insufficient, so add suitable fuel.
Why does my KTM 1290 SUPER ADVENTURE R 2021 Motorcycle engine not rotate when pressing the start button?
If your KTM Motorcycle engine does not rotate when the start button/emergency OFF switch is pressed, it could be due to an operating error, so carry out the start procedure. Another cause could be that the 12-V battery is discharged, so charge the 12-V battery and check the open-circuit current.
Why is my KTM Motorcycle 12-V battery discharged?
If the 12-V battery is discharged on your KTM Motorcycle, it might be due to several reasons. An electrical power consumer might be connected to the socket/ACC1, so disconnect it. The hazard warning flasher might be switched on, so switch it off. The 12-V battery may not be charging, so check the charging voltage. Or, the ignition was not switched off when the vehicle was parked. In any case, consider charging the 12-V battery.
Why does the malfunction indicator lamp light up on my KTM 1290 SUPER ADVENTURE R 2021 Motorcycle?
If the malfunction indicator lamp lights up on your KTM Motorcycle, it indicates a malfunction in the electronic fuel injection. To address this, read out the fault memory using the KTM diagnostics tool.
What does it mean when the ABS warning lamp lights up on my KTM 1290 SUPER ADVENTURE R 2021 Motorcycle?
If the ABS warning lamp lights up on your KTM Motorcycle, it could be due to several reasons. The ABS fuse might be blown, so change the fuses in the fuse box. The wheel speeds of the front and rear wheels might differ greatly, so stop, switch off the ignition, and start again. There might also be a malfunction in the ABS, so read out the fault memory using the KTM diagnostics tool.
Why is nothing showing on the display of my KTM 1290 SUPER ADVENTURE R 2021 Motorcycle?
If the combination instrument on your KTM Motorcycle shows nothing on the display, it could be due to a blown fuse 1, so change the fuses in the fuse box. Another cause could be a burned-out main fuse, so change the main fuse. Finally, the 12-V battery could be discharged, so charge the 12-V battery and check the open-circuit current.
What causes my KTM 1290 SUPER ADVENTURE R 2021 engine to die during the trip?
If your KTM Motorcycle engine dies during the trip, it may be due to a lack of fuel, so refuel. It could also be due to a malfunction in the electronic fuel injection, so read out the fault memory using the KTM diagnostics tool.
Why does my KTM 1290 SUPER ADVENTURE R 2021 Motorcycle engine only turn when the clutch lever is drawn?
If your KTM Motorcycle engine turns only when the clutch lever is drawn, it could be because the vehicle is in gear, so shift the transmission into neutral. It may also be due to a faulty safety starting system, so read out the fault memory using the KTM diagnostics tool.
What does it mean when the RACE ON indicator light flashes twice on my KTM 1290 SUPER ADVENTURE R 2021 Motorcycle?
If the RACE ON indicator light on your KTM Motorcycle flashes twice, it indicates no response signal from the RACE ON key. To resolve this, ensure that the RACE ON key anti-relay attack mode has been deactivated, and the RACE ON key is in range. Also, remove other electronic devices from the vicinity of the RACE-ON antenna, check the battery compartment in the RACE-ON key for correct locking and corrosion, change the RACE-ON key battery and hold RACE ON chip or RACE ON key directly to the vehicle antenna.
Why does my KTM 1290 SUPER ADVENTURE R 2021 Motorcycle engine turn although a gear is engaged?
If your KTM Motorcycle engine turns even when a gear is engaged, it indicates a faulty safety starting system. To address this, read out the fault memory using the KTM diagnostics tool.
General| Engine Type | 2-cylinder, 4-stroke, V 75° |
|---|---|
| Displacement | 1301 cc |
| Transmission | 6-speed |
| Fuel Tank Capacity | 23 liters |
| Seat Height | 880 mm |
| Dry Weight | 221 kg |
| Rear Suspension | WP XPLOR PDS shock absorber |
| Front Tire | 90/90-21 |
| Rear Tire | 150/70-18 |
| Compression Ratio | 13.1:1 |
| Starter | Electric |
| Cooling System | Liquid cooled |
| Lubrication | Forced oil lubrication with 3 oil pumps |
| Traction Control | MTC (Motorcycle Traction Control), lean-angle sensitive |
| Power | 160 hp |
| Torque | 138 Nm |
| Front Suspension | WP XPLOR 48 mm, fully adjustable |
| Front Brake | Dual 320 mm discs, 4-piston calipers |
| Rear Brake | Brembo 2-piston caliper, 267 mm disc |
| ABS | Bosch 9.1MP (Cornering ABS) |
| Ground Clearance | 250 mm |
| Fuel System | Keihin EFI |
| Frame | Chromium-Molybdenum steel trellis frame, powder coated |
Welcome to the owner's manual, providing general information about the motorcycle.
Explains the meaning of various symbols used throughout the manual for clarity.
Details the typographical formats used in the manual, such as proprietary names.
Defines proper vehicle use, highlights misuse dangers, and provides general safety guidelines.
Explains different risk levels (Danger, Warning, Caution) and their associated symbols.
Warnings against tampering, safe operation, and the importance of protective clothing.
Outlines rules for vehicle work and guidelines for environmental responsibility.
Details warranty conditions, service requirements, and dealer support information.
Guidance on recommended fuels, auxiliary substances, and approved spare parts.
Illustrates and labels key components from front left and rear right views.
Details locations for VIN, engine, fork, and shock absorber numbers.
Describes clutch, handbrake, throttle, and left combination switch functions.
Covers RACE ON key, steering lock, immobilizer, and electrical sockets.
Procedures for seat release, luggage rack, stands, and fuel tank access.
Details instrument activation, display modes, and warning indicators.
Explanation of various indicator lamps and their meanings.
Accessing menus, KTM MY RIDE, phone pairing, and navigation.
Configuration options for Ride Modes, MTC, ABS, Throttle Response, and Slip Adjuster.
Adjusting handlebar, windshield, and control lever positions for comfort.
Adjusting footrests and shift lever for optimal rider ergonomics.
Advice for first use, tire run-in, and engine break-in procedures.
Guidelines for safe luggage loading and managing weight limits.
Essential checks before riding and step-by-step engine starting.
Guidance on shifting, braking, and general safe riding practices.
Safe practices for stopping, moving, and fueling the motorcycle.
List of mandatory service tasks and their recommended intervals.
Optional service tasks for optimal vehicle performance.
Instructions for adjusting front and rear suspension damping and preload.
Procedures for using stands, seat, and maintaining the drive chain.
Maintenance for clutch, steering, fairings, engine guard, and crash bars.
Explanation of ABS, brake disc/lining checks, and fluid levels.
Procedures for adding brake fluid and checking brake linings.
Procedures for front/rear wheel service and tire condition/pressure checks.
Instructions for checking tire pressure and spoke tension.
Details on lights, battery service, charging, and fuse replacement.
Adjusting headlight range and using the diagnostics connector.
Locations and function of accessory power outlets.
Procedures for checking and correcting coolant levels.
Selecting ride modes and configuring traction control and throttle response.
Procedures for checking engine oil level and changing oil/filter.
Step-by-step guide for topping up engine oil to the correct level.
Proper methods and precautions for cleaning the motorcycle.
Maintenance tips for protecting the motorcycle during winter.
Procedures for preparing the motorcycle for extended storage.
Steps for getting the motorcycle ready after it has been stored.
Key technical data for engine, chassis, suspension, and brakes.
Details on electrical components and specified torque values for fasteners.
General and country-specific declarations regarding system compliance.
Information on open source software used in vehicle components and its availability.
Specifications for brake fluid, coolant, engine oil, fork oil, and fuel types.
Explanation of relevant industry standards for motorcycle oils.
Explanation of red, yellow, and orange warning symbols.
Explanation of green and blue informational symbols.
To Next Page