KTM 350 EXC-F 2017 User Manual (English)

Other manuals for KTM 350 EXC-F 2017

Questions and Answers:

L
Linda BanksAug 14, 2025
What to do if my KTM 350 EXC-F 2017 engine turns but does not start?
- B
  Brenda DavisAug 14, 2025
  If your KTM Motorcycle's engine can turn over but won't start, a few things could be happening. It might be a simple operating error, so try the start procedure again. Check if the fuel hose connection is properly connected. Also, fuses 1 or 4 might be blown, so replace them. Other potential issues include an incorrectly set idle speed (adjust it), a spark plug that's oily or wet (clean, dry, or replace it), or a spark plug gap that's too wide (adjust to 1.0 mm). More complex problems could involve a defective ignition system (check it), a short-circuit in the wiring harness (inspect visually and check the electrical system), or a defect in the fuel injection system (read the fault memory using the KTM diagnostics tool).
H
holtvanessaAug 17, 2025
What to do if KTM Motorcycle engine dies during the trip?
- J
  Jacob DixonAug 17, 2025
  If your KTM Motorcycle engine dies during a trip, several factors could be the cause. First, check if you're simply out of fuel and refuel if necessary. Fuses 1 and 4 might be blown, so replace them. A low coolant level in the cooling system could also be the culprit; check for leaks and verify the coolant level. Lastly, insufficient airflow can cause the engine to stall, so switch off the engine when stationary.
J
John HuntAug 20, 2025
Why is my KTM 350 EXC-F 2017 engine overheating?
- N
  Nicholas BakerAug 20, 2025
  Several issues can cause a KTM Motorcycle engine to overheat. There might be foam formation in the cooling system, requiring you to drain and refill the coolant. A bent radiator hose should be replaced. A defective thermostat should be checked; the guideline opening temperature is 70 °C (158 °F). Lastly, a defect in the radiator fan system needs investigation; check the radiator fan fuse (fuse 4) and the radiator fan itself.
O
olsondavidAug 25, 2025
Why does my KTM Motorcycle have high oil consumption?
- M
  Matthew PowellAug 25, 2025
  High oil consumption in your KTM Motorcycle can stem from several causes. Check if the engine vent hose is bent, and reroute it without bends or replace it if necessary. Ensure the engine oil level isn't too high. If the engine oil is too thin (low viscosity), change the engine oil and oil filter, and clean the oil screen. Lastly, worn piston and cylinder can contribute to high oil consumption, so measure the piston/cylinder mounting clearance.
C
Cheryl BaileyAug 27, 2025
Why are the lights not working on my KTM Motorcycle?
- E
  Erica BoyleAug 27, 2025
  If the high beam, low beam, tail light, parking light, and license plate lamp are not working on your KTM Motorcycle, it's likely that fuse 2 is blown. Replace the fuse.
W
wheelerjoelAug 30, 2025
Why are the horn, brake light, turn signal, and radiator fan not working on my KTM 350 EXC-F 2017?
- J
  James MasonAug 30, 2025
  If the horn, brake light, turn signal, and radiator fan (if equipped) are not working on your KTM Motorcycle, it is likely that fuse 3 is blown. Replace the fuse.
M
Melissa HensleySep 3, 2025
Why is my KTM 350 EXC-F 2017 battery discharged?
- E
  Edward LopezSep 3, 2025
  A discharged battery on your KTM Motorcycle can occur if the alternator isn't charging it properly. Check the charging voltage and the stator winding of the alternator. Another cause could be an undesired power consumer draining the battery; check the closed current.
I
Ian JonesSep 6, 2025
How to troubleshoot KTM 350 EXC-F 2017 engine that cannot be cranked (electric starter)?
- B
  brianchristensenSep 6, 2025
  If your KTM Motorcycle engine cannot be cranked using the electric starter, several factors could be at play. It might be due to an operating error, so try the start procedure again. The battery might be discharged, so recharge it and check the charging voltage, closed current, and stator winding of the alternator. Another cause could be a blown main fuse, which would require replacement. Finally, the starter relay or starter motor themselves could be defective, requiring a check.
R
Robert ReynoldsSep 9, 2025
What to do if speedometer values are deleted on KTM 350 EXC-F 2017 Motorcycle?
- P
  Patricia RobinsonSep 9, 2025
  If the speedometer values (time, stop watch, lap times) are deleted on your KTM Motorcycle, it's likely that the battery in the speedometer is discharged. Replace the speedometer battery.

KTM 350 EXC-F 2017 Specifications

General

Engine Type	Single cylinder, 4-stroke
Displacement	349.7 cc
Bore x Stroke	88 mm x 57.5 mm
Compression Ratio	12.3:1
Fuel System	Keihin EFI, 42 mm throttle body
Starter	Electric starter
Transmission	6-speed
Final Drive	Chain
Rear Suspension	WP Xplor PDS shock absorber
Ignition	Keihin EMS
Cooling	Liquid cooled
Front Tire	90/90-21
Rear Tire	140/80-18
Seat Height	960 mm
Frame	Central double-cradle type 25CrMo4 steel
Front Suspension	WP USD XPlor 48 mm
Front Brake	260 mm disc
Rear Brake	220 mm disc
Clutch	Wet Multi-Disc DDS Clutch, Brembo Hydraulics
Wheelbase	1482 mm

Summary

Introduction and Customer Information

Customer Details

Section for entering vehicle serial numbers and dealer stamp.

Manual and Legal Information

Contains disclaimers, copyright, and quality assurance statements.

Means of Representation

Explanation of Symbols Used

Details the meaning of various symbols used throughout the manual.

Typographical Format Explanation

Explains the use of specific names, brands, and underlined terms.

Safety Advice

Intended Use Definition

Defines the motorcycle's intended purpose and operational limits.

General Safety Instructions

Emphasizes reading the manual and adhering to safety guidelines.

Risk Degrees and Symbols

Explains danger, warning, caution, and note symbols and their implications.

Overview of Vehicle Labels

Identifies and describes various labels and stickers found on the motorcycle.

Reporting Safety Defects

Provides instructions for reporting vehicle defects to NHTSA and KTM.

Noise Emission Warnings

Warns about operating noise and potential penalties for non-compliance.

Consumer Rights and Warranty Claims

Details consumer rights and procedures for warranty claims.

Tampering Warning

Prohibits tampering with noise control systems and lists prohibited actions.

Safe Operation Practices

Covers safe riding, rider fitness, ventilation, and vehicle condition.

Protective Clothing Requirements

Stresses the importance of wearing appropriate protective clothing for safety.

Work Rules for Maintenance

Guidelines for performing maintenance, including tools and parts.

Environmental Protection Guidelines

Advises on responsible use and disposal of fluids for environmental protection.

Owner's Manual Importance

Emphasizes reading and keeping the manual for proper operation and maintenance.

Important Notes

Manufacturer and Implied Warranty

Explains warranty conditions and voidance due to unauthorized work.

Operating and Auxiliary Substances

Warns about fuel hazards and specifies substance usage.

Spare Parts and Accessories

Recommends using approved KTM parts and authorized installation.

Service Requirements

Highlights the importance of scheduled service for vehicle longevity.

Vehicle Overview

Front Left View

Identifies key components from the front-left perspective.

Rear Right View

Identifies key components from the rear-right perspective.

Vehicle Identification Numbers

Chassis Number Location

Shows the location of the chassis number on the steering head.

Type Label Identification

Indicates the location of the vehicle's type labels.

Key Number Information

Explains the importance of the key number for replacement keys.

Engine Number Location

Shows the location of the engine number on the engine.

Fork Part Number Identification

Identifies the location of the fork part number.

Shock Absorber Article Number

Shows the location of the shock absorber article number.

Motorcycle Controls

Clutch Lever Operation

Describes the clutch lever's location and hydraulic operation.

Hand Brake Lever Function

Identifies the hand brake lever for the front brake.

Throttle Grip Operation

Locates the throttle grip on the right handlebar.

Horn Button Functionality

Explains the location and operation of the horn button.

Light Switch Functions

Details the light switch for low and high beams.

Turn Signal Switch Operation

Explains the operation of the turn signal switch.

Emergency OFF Switch Use

Describes the function of the emergency OFF switch.

Electric Starter Button Function

Locates the electric starter button and its operation.

Indicator Lamps Overview

Lists and explains dashboard indicator lamps.

Ignition Lock Positions

Identifies the ignition lock and its operational positions.

Fuel Filler Cap Opening

Provides instructions and safety for opening the fuel filler cap.

Fuel Filler Cap Closing

Details closing the fuel filler cap and routing the breather hose.

Cold Start Button Operation

Explains the function of the cold start button for cold engines.

Idle Speed Adjustment Screw

Describes how to adjust engine idle speed.

Shift Lever Location

Locates the shift lever on the engine.

Foot Brake Lever Identification

Identifies the foot brake lever for the rear brake.

Side Stand Usage

Explains the location and use of the side stand for parking.

Steering Lock Functionality

Locates the steering lock and its function.

Steering Locking Procedure

Provides instructions for locking the steering and safety notes.

Steering Unlocking Procedure

Details the procedure for unlocking the steering.

Speedometer Functions

Speedometer Overview

Introduces the speedometer and its control buttons.

Speedometer Activation and Test

Explains how to activate the speedometer and perform a display test.

Setting Kilometers or Miles

Guides on setting the unit of measurement for the speedometer.

Configuring Speedometer Functions

Explains how to activate or deactivate various speedometer functions.

Setting the Clock

Provides step-by-step instructions for setting the clock.

Viewing Lap Time

Explains how to view lap times if recorded.

Display Mode: Speed

Describes how to display current vehicle speed in km/h or mph.

Display Mode: Service Hours

Explains how to view engine service hours.

Speedometer Setup Menu

Details navigation and options within the speedometer setup menu.

Setting Measurement Units

Guides on changing units between kilometers and miles.

Display Mode: Time

Describes how to display the current time.

Setting the Speedometer Clock

Provides instructions for setting the speedometer clock.

Display Mode: Lap Time

Explains using the speedometer for lap timing.

Viewing Lap Times

Details how to view recorded lap times and reset them.

Display Mode: Odometer

Describes how to view the total distance traveled.

Display Mode: Trip Master 1

Explains the function of Trip Master 1 for measuring distances.

Display Mode: Trip Master 2

Describes the function of Trip Master 2 for navigation.

Setting Trip Master 2

Guides on manually adjusting the Trip Master 2 value.

Display Mode: Average Speed 1

Explains how the speedometer calculates and displays average speed 1.

Display Mode: Average Speed 2

Describes the calculation and display of average speed 2.

Display Mode: Stop Watch 1

Explains how Stop Watch 1 measures riding time.

Display Mode: Stop Watch 2

Details the function of Stop Watch 2 as a manual stopwatch.

Speedometer Function Table

Summarizes operations and button functions for speedometer modes.

Speedometer Menu Activation Table

Shows conditions for activating speedometer functions and menus.

Preparing for Use

Advice for First Use

Provides essential advice for initial operation, rider fitness, and pre-ride checks.

Engine Running-In Procedure

Details the procedure and guidelines for the engine break-in period.

Low-Temperature Battery Performance

Explains how low temperatures affect lithium-ion battery starting power.

Preparation for Difficult Riding

Advises on preparing the vehicle for challenging riding environments.

Riding Preparation: Dry Sand

Provides specific preparation steps for riding in dry sand.

Riding Preparation: Wet Sand

Details preparation measures for riding in wet sand conditions.

Riding Prep: Wet/Muddy Surfaces

Offers advice for riding on wet and muddy terrain.

Riding Prep: High Temp/Slow Speed

Outlines preparations for riding in hot conditions and at low speeds.

Riding Prep: Low Temp/Snow

Provides guidance for preparing for cold or snowy conditions.

Riding Instructions

Pre-Ride Checks and Maintenance

Lists essential pre-ride checks and maintenance tasks for safe operation.

Starting the Motorcycle

Covers the procedure for starting the motorcycle, including safety warnings.

Starting Off Safely

Explains how to safely start moving the motorcycle.

Gear Shifting and Riding Techniques

Details gear shifting and general riding advice.

Braking Techniques and Warnings

Provides essential information and warnings about motorcycle braking.

Stopping and Parking Procedures

Covers safe procedures for stopping and parking.

Motorcycle Transport Guidelines

Offers advice on safely transporting the motorcycle.

Refueling Procedures and Safety

Details the procedure and safety precautions for refueling.

Service Schedule

Additional Service Information

Notes that additional work may be invoiced separately.

Required Maintenance Tasks

Lists scheduled maintenance tasks and their intervals.

Recommended Maintenance Tasks

Outlines recommended maintenance tasks beyond the required schedule.

Chassis Tuning

Basic Suspension Setting by Rider Weight

Explains how to adjust suspension based on rider weight.

Shock Absorber: Compression Damping

Introduces high-speed and low-speed compression damping.

Adjusting Low-Speed Compression Damping

Guides on adjusting low-speed compression damping for comfort.

Adjusting High-Speed Compression Damping

Details adjusting high-speed compression damping for landing.

Adjusting Rebound Damping (Shock Absorber)

Explains adjusting rebound damping for suspension response.

Measuring Unloaded Rear Wheel Dimension

Describes measuring unloaded rear wheel dimension for suspension.

Checking Static Sag (Shock Absorber)

Guides on checking static sag for proper initial suspension load.

Checking Riding Sag (Shock Absorber)

Explains checking riding sag with rider and gear for tuning.

Adjusting Spring Preload (Shock Absorber)

Provides steps for adjusting shock absorber spring preload.

Adjusting Riding Sag (Shock Absorber)

Details adjusting riding sag by selecting springs.

Checking Basic Fork Setting

Discusses fork settings and need for harder springs.

Adjusting Fork Compression Damping

Guides on adjusting fork compression damping.

Adjusting Fork Rebound Damping

Explains adjusting fork rebound damping.

Handlebar Position Options

Shows how handlebar clamps can be mounted in different positions.

Adjusting Handlebar Position

Provides instructions for adjusting handlebar position.

Chassis Service Procedures

Raising Motorcycle with Lift Stand

Details the procedure for safely lifting the motorcycle with a stand.

Removing Motorcycle from Lift Stand

Explains how to safely remove the motorcycle from the lift stand.

Bleeding Fork Legs

Guides on bleeding air from the front fork legs.

Cleaning Fork Dust Boots

Instructions for cleaning fork dust boots to prevent seal leaks.

Removing Fork Protectors

Details the steps for removing fork protectors.

Installing Fork Protectors

Provides instructions for installing fork protectors with torque specs.

Removing Fork Legs

Explains the procedure for removing the front fork legs.

Installing Fork Legs

Guides on installing front fork legs with torque specifications.

Removing Lower Triple Clamp

Details the process for removing the lower triple clamp.

Installing Lower Triple Clamp

Guides on installing the lower triple clamp, including bearing lubrication.

Checking Steering Head Bearing Play

Explains how to check for play in the steering head bearing.

Adjusting Steering Head Bearing Play

Provides instructions for adjusting steering head bearing play.

Lubricating Steering Head Bearing

Details the procedure for lubricating steering head bearings.

Removing Front Fender

Guides on how to remove the front fender.

Installing Front Fender

Provides instructions for installing the front fender.

Removing Shock Absorber

Details the steps for removing the rear shock absorber.

Installing Shock Absorber

Guides on installing the rear shock absorber with torque specifications.

Removing Seat

Explains how to remove the motorcycle seat.

Mounting Seat

Provides instructions for mounting the motorcycle seat.

Removing Air Filter Box Cover

Details how to remove the air filter box cover.

Installing Air Filter Box Cover

Guides on installing the air filter box cover.

Removing Air Filter

Explains how to remove the air filter and warns against running without it.

Installing Air Filter

Provides instructions for installing a clean air filter.

Cleaning Air Filter and Box

Details the proper procedure for cleaning the air filter and box.

Sealing Air Filter Box

Instructions for sealing the air filter box.

Securing Air Filter Box Cover

Explains how to secure the air filter box cover.

Removing Main Silencer

Guides on removing the main silencer, with warnings about heat.

Installing Main Silencer

Provides instructions for installing the main silencer.

Cleaning Spark Arrestor

Explains how to clean the spark arrestor.

Changing Silencer Filling

Details replacing glass fiber yarn in the main silencer.

Removing Fuel Tank

Provides instructions and safety warnings for removing the fuel tank.

Installing Fuel Tank

Guides on installing the fuel tank, including safety and connections.

Checking Chain Dirt Accumulation

Explains how to check the motorcycle chain for dirt buildup.

Cleaning the Motorcycle Chain

Details the procedure for cleaning and lubricating the motorcycle chain.

Checking Chain Tension

Explains how to check and the importance of correct chain tension.

Adjusting Chain Tension

Provides step-by-step instructions for adjusting chain tension.

Checking Chain, Sprockets, and Guide

Guides on inspecting wear on the chain, sprockets, and guide.

Checking Chain Sliding Piece and Guide

Continues inspection of chain sliding pieces and guides.

Checking the Frame

Details how to check the motorcycle frame for damage.

Checking the Swingarm

Explains how to inspect the swingarm for damage.

Checking Throttle Cable Routing

Guides on verifying correct throttle cable routing.

Checking Handlebar Rubber Grips

Details checking handlebar rubber grips for damage or wear.

Adjusting Clutch Lever Position

Explains how to adjust the clutch lever position.

Checking/Correcting Clutch Fluid Level

Guides on checking and correcting the hydraulic clutch fluid level.

Changing Hydraulic Clutch Fluid

Provides a detailed procedure for changing the hydraulic clutch fluid.

Brake System Maintenance

Checking Hand Brake Lever Free Travel

Explains how to check and set hand brake lever free travel.

Adjusting Hand Brake Lever Free Travel

Guides on adjusting the hand brake lever free travel.

Checking Brake Discs

Details checking brake disc thickness and for damage.

Checking Front Brake Fluid Level

Guides on checking front brake fluid level and potential issues.

Adding Front Brake Fluid

Explains how to add front brake fluid and safety precautions.

Checking Front Brake Linings

Details checking front brake lining thickness and for damage.

Changing Front Brake Linings

Provides instructions for changing front brake linings.

Checking Foot Brake Lever Free Travel

Guides on checking and setting foot brake lever free travel.

Adjusting Foot Brake Lever Position

Details adjusting the basic position of the foot brake lever.

Checking Rear Brake Fluid Level

Guides on checking rear brake fluid level and potential issues.

Adding Rear Brake Fluid

Explains how to add rear brake fluid and safety precautions.

Checking Rear Brake Linings

Details checking rear brake lining thickness and for damage.

Changing Rear Brake Linings

Provides instructions for changing rear brake linings.

Changing Rear Brake Linings (Continued)

Continues instructions for changing rear brake linings.

Changing Rear Brake Linings (Final Steps)

Final steps for changing rear brake linings and adding brake fluid.

Wheels and Tires

Removing the Front Wheel

Provides steps for removing the front wheel, including brake caliper adjustment.

Installing the Front Wheel

Guides on installing the front wheel, including bearing checks.

Removing the Rear Wheel

Details the procedure for removing the rear wheel.

Installing the Rear Wheel

Guides on installing the rear wheel, including chain and brake adjustments.

Checking Tire Condition

Explains how to check tires for wear, damage, and age.

Checking Tire Air Pressure

Details checking and adjusting tire air pressure.

Checking Spoke Tension

Guides on checking spoke tension for wheel integrity.

Electrical System

Removing the Battery

Provides instructions for safely removing the motorcycle battery.

Installing the Battery

Guides on installing the motorcycle battery with proper connections.

Recharging the Battery

Details battery recharging procedures and precautions.

Changing the Main Fuse

Explains how to change the main fuse.

Changing Fuses for Power Consumers

Guides on locating and changing fuses for various components.

Removing Headlight Assembly

Details the procedure for removing the headlight assembly.

Installing Headlight Assembly

Provides instructions for reinstalling the headlight assembly.

Changing Headlight Bulb

Guides on replacing the headlight bulb.

Changing Turn Signal Bulb

Explains how to change a turn signal bulb.

Checking Headlight Setting

Details how to check and verify correct headlight beam alignment.

Adjusting Headlight Range

Guides on adjusting the headlight beam range.

Changing Speedometer Battery

Provides instructions for replacing the speedometer battery.

Diagnostics Connector Location

Locates the diagnostics connector under the seat.

Cooling System

Cooling System Overview

Briefly explains the function of cooling system components.

Checking Antifreeze and Coolant Level

Guides on checking antifreeze concentration and coolant level.

Checking Coolant Level in Radiator

Details checking radiator coolant level with safety precautions.

Draining the Coolant

Provides instructions for draining the motorcycle's coolant.

Refilling the Cooling System

Guides on refilling the cooling system and checking for leaks.

Engine Tuning

Checking Throttle Cable Play

Explains how to check throttle cable play.

Adjusting Throttle Cable Play

Guides on adjusting throttle cable play.

Setting Throttle Response Map

Details changing throttle response using guide plates.

Adjusting Idle Speed

Provides instructions for adjusting engine idle speed.

Teaching Throttle Valve Position

Explains the procedure for teaching throttle valve position.

Checking Basic Shift Lever Position

Guides on checking shift lever basic position.

Adjusting Basic Shift Lever Position

Details how to adjust the basic position of the shift lever.

Engine Service Procedures

Changing the Fuel Screen

Provides instructions for changing the fuel screen.

Checking Engine Oil Level

Guides on checking the engine oil level.

Engine Oil and Filter Change

Details changing engine oil, filter, and cleaning oil screen.

Adding Engine Oil

Explains how to add engine oil and safety precautions.

Cleaning and Care

Motorcycle Cleaning Procedure

Provides detailed instructions and warnings for cleaning the motorcycle.

Winter Operation Checks and Maintenance

Outlines checks and maintenance for protecting the motorcycle during winter.

Storage and Preparation

Motorcycle Storage Procedures

Details steps and precautions for storing the motorcycle.

Preparing for Use After Storage

Guides on preparing the motorcycle for use after storage.

Troubleshooting Guide

Troubleshooting Engine Issues

Covers faults related to engine starting, speed, and power.

Troubleshooting Other Issues

Covers faults like overheating, indicator lamps, and oil consumption.

Technical Data

Engine Specifications

Lists detailed technical specifications for the motorcycle's engine.

Engine Tightening Torques

Provides a table of torque specifications for engine components.

Fluid Capacities

Lists the various fluid capacities of the motorcycle.

Chassis Dimensions and Specifications

Provides technical data related to the chassis and dimensions.

Electrical System Components

Lists specifications for electrical system components.

Tire Specifications

Specifies tire sizes and types.

Front Fork Specifications

Provides technical details and settings for the front fork.

Shock Absorber Specifications

Lists technical specifications and adjustment ranges for the shock absorber.

Chassis Tightening Torques

Details torque specifications for chassis fasteners.

Chassis Tightening Torques (Continued)

Continues the table of chassis tightening torques.

Recommended Substances and Fluids

Brake Fluid Specifications

Specifies standards and recommendations for brake fluid.

Coolant Specifications

Details coolant specifications, mixture ratios, and recommended brands.

Engine Oil (SAE 10W/60)

Specifies standards and recommendations for SAE 10W/60 engine oil.

Engine Oil (SAE 10W/50)

Specifies standards and recommendations for SAE 10W/50 engine oil.

Fork Oil Specifications

Specifies standards and recommendations for fork oil.

Shock Absorber Fluid Specifications

Specifies standards and recommendations for shock absorber fluid.

Fuel Grade Guidelines

Provides guidelines for using super unleaded fuel, including ethanol content.

Auxiliary Substances and Cleaners

Air Filter Cleaner Recommendations

Lists recommended suppliers and products for air filter cleaning.

Chain Cleaner Recommendations

Lists recommended suppliers and products for chain cleaning.

Fuel Additive Recommendations

Lists recommended suppliers and products for fuel additives.

High Viscosity Grease Recommendations

Lists recommended suppliers and products for high viscosity grease.

Long-Life Grease Recommendations

Lists recommended suppliers and products for long-life grease.

Motorcycle Cleaner Recommendations

Lists recommended suppliers and products for motorcycle cleaning.

Off-Road Chain Spray Recommendations

Lists recommended suppliers and products for off-road chain spray.

Foam Air Filter Oil Recommendations

Lists recommended suppliers and products for foam air filter oil.

Surface Protection Material Recommendations

Lists recommended suppliers and products for protecting surfaces.

Special Cleaner Recommendations

Lists recommended cleaners for various surface finishes.

Universal Oil Spray Recommendations

Lists recommended suppliers and products for universal oil spray.

Industry Standards

JASO T903 MA Standard Explained

Explains the JASO T903 MA standard for motorcycle engine oils.

SAE Viscosity Classification Explained

Explains the SAE classification system for oil viscosity.

Index of Special Terms

OBD Definition

Defines On-board diagnosis (OBD) as a system monitoring emission and safety values.

List of Symbols

Yellow and Orange Symbols Explained

Explains yellow/orange symbols indicating error conditions or active driving aids.

Green and Blue Symbols Explained

Explains green/blue symbols that reflect general information.

Related product manuals

KTM 350 EXC-F EU 2018