KTR-Group ROTEX GS - 1.2 Torques and finish bores

ROTEX
®
GS
Operating/Assembly instructions
KTR-N
Sheet:
Edition:
45510 EN
5 of 40
23
Please observe protection
note ISO 16016.
Drawn:
2020-02-10 Pz/Ht
Replacing:
KTR-N dated 2019-11-22
Verified:
2020-02-10 Pz
Replaced by:
Table 1: Torques of spiders
Size
Spider
1)
(component 2)
Rated torque [Nm]
80 ShA-GS
92 ShA-GS
98 ShA-GS
64 ShD-GS
72 ShD-GS
2)
5
0.3
0.5
0.9
-
-
7
0.7
1.2
2.0
2.4
-
8
0.7
-
2.0
2.4
-
9
1.8
3.0
5.0
6.0
-
12
3.0
5.0
9.0
12.0
-
13
3.6
-
11.0
14.5
-
14
4.0
7.5
12.5
16.0
-
16
5.0
-
15.0
19.0
-
19
6
12
21
26
-
24
-
35
60
75
97
28
-
95
160
200
260
38
-
190
325
405
525
42
-
265
450
560
728
48
-
310
525
655
852
55
-
410
685
825
1072
65
-
-
940
1175
1527
75
-
-
1920
2400
3120
90
-
-
3600
4500
5850
1) Maximum torque of the coupling T
Kmax.
= rated torque of the coupling T
K rated
x 2
For coupling selection see catalogue drive technology "ROTEX
®
GS"
2) When using the spider 72 ShD, we recommend to use hubs made of steel.
Table 2: Finish bores
Size
Unbore
d
Finish bore [mm]
d
min.
d
max.
for hub type
1.0
1.1
1.2
2.0
2.1
2.5
2.6
2.8
2.9
6.0
light
6.0
5
-
2
-
6
5
5
-
-
-
-
-
-
-
7
-
3
7
7
7
7
7
-
-
7
7
-
-
8
-
-
-
-
-
-
-
-
-
8
8
-
-
9
-
4
10
11
11
11
11
-
-
9
9
-
-
12
-
4
12
12
12
12
12
-
-
12
12
-
-
13
-
-
-
-
-
-
-
-
-
12.7
12.7
-
-
14
-
5
16
16
16
16
16
-
-
16
16
14
-
16
-
-
-
-
-
-
-
-
-
16
16
-
-
19
x
6
24
-
-
-
-
24
24
27
27
20
20
24
x
8
28
-
-
-
-
28
28
32
32
32
28
28
x
10
38
-
-
-
-
38
38
35
35
38
38
38
x
12
45
-
-
-
-
45
45
45
45
48
48
42
x
14
55
-
-
-
-
50
45
-
-
51
51
48
x
15
62
-
-
-
-
55
55
-
-
55
55
55
x
20
74
-
-
-
-
68
68
-
-
70
65
x
22
80
-
-
-
-
70
70
-
-
70
75
x
30
95
-
-
-
-
80
80
-
-
80
90
-
40
110
-
-
-
-
90
90
-
-
105
1 Technical data
1.2 Torques and finish bores