Kubota DMC 8032 User Manual (English)

Questions and Answers:

M
Matthew PierceAug 5, 2025
Why is there uneven stubble with Kubota DMC 8032 Farm Equipment?
- S
  Sarah RodriguezAug 5, 2025
  If you notice uneven stubble when using your Kubota Farm Equipment, several factors could be at play. It might be caused by driving too slowly, so try increasing your speed. Alternatively, the tractor RPM on the P.T.O. could be too low, in which case you should check the RPM. Also, inspect the blades; if they are blunt or missing, turn or replace them. Finally, the machine may not be correctly balanced, so adjust the springs.
W
Wendy MillerAug 9, 2025
Why is the conditioning too weak on my Kubota DMC 8032 Farm Equipment?
- S
  Stephanie LittleAug 10, 2025
  If the conditioning is too weak on your Kubota Farm Equipment, there are several things to check. First, adjust the roller pressure if it's too low. If your driving speed is too high, reduce it. Also, make sure to check the V-belts at the roller to ensure they are sufficiently tightened. Finally, if the roller V-belts are worn, replace them.
D
Daniel LewisAug 13, 2025
Why are there stripes in the stubble with Kubota Farm Equipment?
- B
  Brandi GutierrezAug 13, 2025
  If you notice stripes in the stubble when using your Kubota Farm Equipment, it could be because the cutterbar is not correctly angled for the crop in question, so adjust the angle of the cutterbar. Another possible cause is that the cutterbar is fitted with high skids, so remove the high skids.
J
Jennifer EllisAug 17, 2025
What to do if there are uneven swathes with Kubota DMC 8032?
- M
  monicamooreAug 18, 2025
  If your Kubota Farm Equipment is producing uneven swathes, the rotor's RPM may be too low, so adjust the rotation of the rollers to 1200 RPM. Additionally, the deflector plate might be incorrectly set, so adjust the deflector plates.
E
Erin HendricksAug 22, 2025
Why does the cutterbar get abnormally warm on Kubota Farm Equipment?
- A
  amanda85Aug 22, 2025
  If the cutterbar on your Kubota Farm Equipment gets abnormally warm, it could be caused by too much oil in the cutterbar, so inspect the oil level. Alternatively, the wrong oil type could be the issue, so change to the correct oil type.
S
Sarah SaundersAug 27, 2025
What to do if the cutting unit receives violent shocks during road transport with Kubota DMC 8032?
- C
  Christopher MitchellAug 27, 2025
  If the cutting unit of your Kubota Farm Equipment receives violent shocks during road transport, the machine's accumulator may have too little pressure or is defective, so check or replace the accumulator. Also, the safety valve may be closed, ensure that the safety valve is open.
S
sullivankerryAug 30, 2025
Why is Kubota DMC 8032 Farm Equipment sloping to the rear during mowing?
- N
  nhernandezAug 30, 2025
  If your Kubota Farm Equipment is sloping to the rear during mowing, it indicates there is too much downward pressure on the cutterbar. Adjust the springs to resolve this issue.

Kubota DMC 8032 Specifications

General

Brand	Kubota
Model	DMC 8032
Category	Farm Equipment
Language	English

Summary

Preface

For your own safety

Emphasizes reading the manual for optimal conditions and safety.

Safety

Safety labels

Locating and understanding safety labels on the machine for hazard awareness.

Transport on public roads

Safety guidelines and requirements for transporting the machine on public roads.

Who can operate the machine?

Attachment

Instructions and safety precautions for correctly attaching the machine to a tractor.

Load capacity

Guidelines on complying with weight limits, axle pressure, and tire capacity.

Use

General instructions and precautions for safe operation of the machine.

Disconnection

Safety measures and procedures to follow when disconnecting the machine from the tractor.

Maintenance

Importance of following service intervals and using original spare parts for safety.

Further safety instructions

Preparation

Preparing the machine

Length of P.T.O. shaft

Swivel gear

Assembly - attachment

Attachment of the tractor

Covers the critical steps and safety warnings for coupling the machine to the tractor.

Lock the tractor's lift arms

Details how to lock lift arms to prevent PTO shaft damage and ensure safety.

Secure the attachment with the locking pin

Stresses the importance of using a locking pin to prevent detachment and ensure safety.

P.T.O. shaft

Provides instructions for installing the P.T.O. shaft correctly and safely.

Hydraulics

Safety precautions and procedures for connecting and handling the hydraulic system.

Initial startup of machine

Steps for the first test drive, including guard checks and PTO connection.

Friction clutch

Machine in the transport mode

Transport on public roads

General

Compliance with local laws for lights, reflective requirements, and vehicle weight.

Before traveling on public roads

Pre-travel checks including hydraulic functions, PTO, and surrounding area safety.

Checking the machine

A checklist for verifying the machine is in transport mode and all systems are functional.

Speed when driving on public roads

Specifies the maximum permitted speed for safe road transportation.

Operation

Safety

General safety warnings and guidelines for operating the machine.

Before operating

Essential checks and safety measures to perform before starting operation.

Operating

Step-by-step instructions for operating the machine in the field.

Roller pressure

Changing the roller pressure

Distance between rollers

Deflector plates

Stubble height

Balancing the cutting unit

Working in the field

Specific operational steps for the 80xx model in the field.

Cleaning

Before cleaning

Cleaning

After cleaning

Parking and Storage

Before storage

Parking/disconnection of the machine

Critical safety steps for safely disconnecting the machine from the tractor.

Hydraulics

Storage

Maintenance

For your own safety

Emphasizes compliance with service intervals and the risks of incorrect maintenance.

Specific safety information

Key safety points for performing repair and maintenance work.

Lubrication safety and use of oil

General instruc tions

Maintenance intervals

A detailed schedule of checks, lubrication, and replacement tasks based on usage.

Lubrication

Service - check

Blades

Cone

Universal joint

Stone guard and counter blade

Rollers

Transmission

Friction clutch

Wheel

Replacement

Changing oil

Troubleshooting

Electric and hydraulic system

Lists common faults, causes, and solutions for hydraulic system issues.

Cutterbar

Addresses issues like sloping, uneven stubble, stripes, and shocks related to the cutterbar.

P.T.O. shaft

Troubleshoots problems with conditioning, crop flow blockage, and PTO shaft warmth.

Warranty

Guidelines for warranty

EU Declaration of Conformity

EU Directive 2006/42/EC

Technical information

Lubricants

Torque moment

Related product manuals

Kubota DMC 8032 User Manual

Table of Contents

Questions and Answers:

Kubota DMC 8032 Specifications

Summary

Preface

For your own safety

Safety

Safety labels

Transport on public roads

Who can operate the machine?

Attachment

Load capacity

Use

Disconnection

Maintenance

Further safety instructions

Preparation

Preparing the machine

Length of P.T.O. shaft

Swivel gear

Assembly - attachment

Attachment of the tractor

Lock the tractor's lift arms

Secure the attachment with the locking pin

P.T.O. shaft

Hydraulics

Initial startup of machine

Friction clutch

Machine in the transport mode

Transport on public roads

General

Before traveling on public roads

Checking the machine

Speed when driving on public roads

Operation

Safety

Before operating

Operating

Roller pressure

Changing the roller pressure

Distance between rollers

Deflector plates

Stubble height

Balancing the cutting unit

Working in the field

Cleaning

Before cleaning

Cleaning

After cleaning

Parking and Storage

Before storage

Parking/disconnection of the machine

Hydraulics

Storage

Maintenance

For your own safety

Specific safety information

Lubrication safety and use of oil

General instruc tions

Maintenance intervals

Lubrication

Service - check

Blades

Cone

Universal joint

Stone guard and counter blade

Rollers

Transmission

Friction clutch

Wheel

Replacement

Changing oil

Troubleshooting

Electric and hydraulic system

Cutterbar

P.T.O. shaft

Warranty

Guidelines for warranty

EU Declaration of Conformity