Kurzweil K2600 V2.0 - MUSICIANS GUIDE SUPPLEMENT REV A - Triple Algorithm Reference

2-12
Triple Modular Processing
Algorithm Reference
Algorithm Reference
This section contains a diagram for each triple
algorithm, as you see it in the K2600’s display. Below
each diagram is a list of the DSP functions available in
each block of the algorithm.
Layer-1 Algorithms (33–62)
Algorithm:33
||||||||||||||||||||||||||||||||||||||||
qwwerwwtqwwerwwwwwwerwwtqwwerwwwwwwerwt|
d||||||gk||||||||||||||gk|||||||||||||j|
CVVVVVVBCVVVVVVVVVVVVVVBCVVVVVVVVVVVVVM|
Algorithm:34
||||||||||||||||||||||||||||||||||||||||
qwwerwwtqwwerwwtqwwerwwwwwwerwwtqwwerwt|
d||||||gk||||||gk||||||||||||||gk|||||j|
CVVVVVVBCVVVVVVBCVVVVVVVVVVVVVVBCVVVVVM|
PITCH NONE NONE
2PARAM SHAPER 2PARAM SHAPER
LOPAS2 GAIN LOPAS2 GAIN
2POLE LOWPASS 2POLE LOWPASS
BANDPASS FILT BANDPASS FILT
NOTCH FILTER NOTCH FILTER
2POLE ALLPASS 2POLE ALLPASS
PARA BASS PARA BASS
PARA TREBLE PARA TREBLE
PARA MID PARA MID
PITCH NONE NONE NONE
AMP 2PARAM SHAPER AMP
LOPASS LOPAS2 GAIN LOPASS
HIPASS 2POLE LOWPASS HIPASS
ALPASS BANDPASS FILT ALPASS
GAIN NOTCH FILTER GAIN
SHAPER 2POLE ALLPASS SHAPER
DIST PARA BASS DIST
PWM PARA TREBLE PWM
SINE PARA MID SINE
LF SIN LF SIN
SW+SHP SW+SHP
SAW+ SAW+
SAW SAW
LF SAW LF SAW
SQUARE SQUARE
LF SQR LF SQR
WRAP WRAP
Algorithm:35
||||||||||||||||||||||||||||||||||||||||
qwwerwwtqwwerwwwwwwerwwtqwwerwwtqwwerwt|
d||||||gk||||||||||||||gk||||||gk|||||j|
CVVVVVVBCVVVVVVVVVVVVVVBCVVVVVVBCVVVVVM|
Algorithm:36
||||||||||||||||||||||||||||||||||||||||
qwwerwwtqwwerwwtqwwerwwtqwwerwwwwwwerwt|
d||||||gk||||||gk||||||gk|||||||||||||j|
CVVVVVVBCVVVVVVBCVVVVVVBCVVVVVVVVVVVVVM|
PITCH NONE NONE NONE
2PARAM SHAPER AMP AMP
LOPAS2 GAIN LOPASS LOPASS
2POLE LOWPASS HIPASS HIPASS
BANDPASS FILT ALPASS ALPASS
NOTCH FILTER GAIN GAIN
2POLE ALLPASS SHAPER SHAPER
PARA BASS DIST DIST
PARA TREBLE PWM PWM
PARA MID SINE SINE
LF SIN LF SIN
SW+SHP SW+SHP
SAW+ SAW+
SAW SAW
LF SAW LF SAW
SQUARE SQUARE
LF SQR LF SQR
WRAP WRAP
PITCH NONE NONE NONE
AMP AMP 2PARAM SHAPER
LOPASS LOPASS LOPAS2 GAIN
HIPASS HIPASS 2POLE LOWPASS
ALPASS ALPASS BANDPASS FILT
GAIN GAIN NOTCH FILTER
SHAPER SHAPER 2POLE ALLPASS
DIST DIST PARA BASS
PWM PWM PARA TREBLE
SINE SINE PARA MID
LF SIN LF SIN
SW+SHP SW+SHP
SAW+ SAW+
SAW SAW
LF SAW LF SAW
SQUARE SQUARE
LF SQR LF SQR
WRAP WRAP