These paper types will cause slower printing when the paper is fed from the MP tray. 2-21 2.
9. Sleep (Ecopower) Mode 2.9. Sleep (Ecopower) Mode The printer has a sleep timer to conserve power when the printer is not printing, processing, or
receiving data. You can adjust the timer value, the length of time the printer waits before entering sleeping mode in the absence of data. Any value from 0 to
120 [minutes] (the factory setting is 30 [minutes]) can be entered in 5-minute increments. You can use the or key to move the cursor back and forth through
the figures to rapidly set a large value. If the printer receives no data for the period adjusted as above, it times out and enters into sleeping mode,
indicatingý6OHHSLQJ on the message display. When you send data for printing to the printer again or press a key on the control panel, the printer starts
warming up, indicatingý3OHDVH ZDLW, and becomes ready and on-line. Opening and closing the printer's top cover or drawing out and closing the current
paper cassette also awakens the printer to start warming up and become ready.
The printer also enters into sleeping mode if it times out while MODE SELECTing, or requesting the addition of paper or toner, indicating the appropriate
maintenance message on its message display. The printer environment last set is still maintained even though all indicators are out while the printer is
iný6OHHSLQJ mode. 2-22 2.10. Dumping Received Data 2.
10. Dumping Received Data It is possible to print data received by the printer as hexadecimal code for the purposes of debugging programs and files. 1.
Pressing the ENTER key once whileý!3ULQWý+(;ð'803 is shown on the message display will cause aý" to display. 2.
Pressing the ENTER key once again,ý3URFHVVLQJ will be shown for a second then the message :DLWLQJ will appear on the message display. 3. Send data
to be dumped to the printer. The messageý3URFHVVLQJ will be displayed during receiving the data. Once the dumped data you require has been output, it is
possible to cancel the printing of any further dumped data by taking the printer offline by pressing the ON LINE key and then pressing the CANCEL key. 4.
Once all data has been received, the messageý:DLWLQJ will appear. Press the FORM FEED key to finish printing. 2-23 2.11.
KIR 2 Level 2.11. KIR 2 Level This printer incorporates the KIR 2 (Kyocera Image Refinement 2) smoothing function. At resolutions of 600 dpi and 300 dpi,
this function provides high print quality by providing software enhancement of print resolution. The function does not operate at 1200 dpi because that is the
maximum resolution attainable by the print engine.). KIR 2 provides high quality printing by providing a software-type improvement to the resolution. Q The
KIR setting isý2II. The KIR setting isý2Q. Set the print density toýíê when setting the KIR 2 mode.
For details on print density, see page 2-26. You can look at the check line, the last line on a status page, to make the optimum KIR 2 mode setting. Status Page
KIR Checking Lines 2-24 2.12. Ecoprint Mode Optimized stripes The current KIR setting is optimal.
Dark vertical stripes Set the KIR mode toý2II. Try printing the status page again. If you still get dark vertical stripes, adjust the print density control to a
lighter setting. (See the last page in this manual.) White vertical stripes Set the KIR mode toý2Q.
Try printing the status page again. If you still get white vertical stripes, adjust the print density control to a darker setting. (See the last page in this manual.)
2.12. Ecoprint Mode The Ecoprint enables you to reduce the amount of toner consumed on the page so as to save your printing costs. You can set to Ecoprint
mode on, as follows. (The factory-setting isý2II. ) The Ecoprint mode setting isý2Q when the printing image becomes lighter, yet very readable. The Ecoprint
setting has no effect on the print speed.
Ecoprint setting isý 2II (default). Ecoprint setting isý 2Q 2-25 2.
You're reading an excerpt. Click here to read official KYOCERA
FS-1750 user guide
http://somemanuals.com/dref/324820
To Next Page
Loading...
