Kyocera FS-9130DN Service Manual

2GZ/2G1-2
1-5-2 Paper feed section..................................................................................................................................1-5-2
(1) Detaching and refitting the forwarding, paper feed and separation pulleys ......................................1-5-2
(2) Detaching and refitting the MP separation, MP paper feed and MP forwarding pulleys ...................1-5-4
(3) Detaching and refitting the left and right registration cleaner............................................................1-5-9
1-5-3 Laser scanner unit ................................................................................................................................1-5-11
(1) Detaching and refitting the laser scanner unit.................................................................................1-5-11
(2) Adjusting the skew of the laser scanner unit (reference) ................................................................1-5-13
1-5-4 Drum section.........................................................................................................................................1-5-14
(1) Detaching and refitting the drum unit ..............................................................................................1-5-14
(2) Detaching and refitting the main charger unit..................................................................................1-5-15
(3) Detaching and refitting the drum separation claws .........................................................................1-5-16
1-5-5 Developing section................................................................................................................................1-5-17
(1) Detaching and refitting the developing unit .....................................................................................1-5-17
1-5-6 Transfer section ....................................................................................................................................1-5-18
(1) Detaching and refitting the transfer roller unit .................................................................................1-5-18
1-5-7 Fuser section ........................................................................................................................................1-5-19
(1) Detaching and refitting the fuser unit...............................................................................................1-5-19
(2) Detaching and refitting the heat roller separation claws..................................................................1-5-20
(3) Detaching and refitting the press roller............................................................................................1-5-21
(4) Detaching and refitting the fuser heater..........................................................................................1-5-22
(5) Detaching and refitting the heat roller .............................................................................................1-5-23
(6) Detaching and refitting the fuser unit thermistor 1 and 2.................................................................1-5-24
1-5-8 Others ...................................................................................................................................................1-5-25
(1) Detaching and refitting the ozone filter 1 and 2...............................................................................1-5-25
(2) Detaching and refitting the dust filter 1 and 2..................................................................................1-5-26
1-6 Firmware
1-6-1 Downloading firmware ............................................................................................................................1-6-1
(1) Downloading the firmware from the parallel interface .......................................................................1-6-2
(2) Downloading the firmware from the memory card.............................................................................1-6-3
(3) Downloading the firmware from the USB memory ............................................................................1-6-5
2-1 Mechanical construction
2-1-1 Paper feed section..................................................................................................................................2-1-1
2-1-2 Main charging section.............................................................................................................................2-1-4
2-1-3 Optical section ........................................................................................................................................2-1-5
(1) Laser scanner unit.............................................................................................................................2-1-5
2-1-4 Developing section..................................................................................................................................2-1-8
(1) Single component developing system.............................................................................................2-1-10
2-1-5 Transfer and separation sections..........................................................................................................2-1-11
2-1-6 Cleaning and charge erasing sections..................................................................................................2-1-12
2-1-7 Fuser section ........................................................................................................................................2-1-13
2-1-8 Eject and switchback sections ..............................................................................................................2-1-14
2-1-9 Duplex section ......................................................................................................................................2-1-15
(1) Paper conveying operation in duplex copying.................................................................................2-1-16
2-2 Electrical Parts Layout
2-2-1 Electrical parts layout..............................................................................................................................2-2-1
(1) PWBs ................................................................................................................................................2-2-1
(2) Switches and sensors .......................................................................................................................2-2-2
(3) Motors ...............................................................................................................................................2-2-4
(4) Other electrical components..............................................................................................................2-2-5
2-3 Operation of the PWBs
2-3-1 Power source PWB.................................................................................................................................2-3-1
2-3-2 Engine PWB............................................................................................................................................2-3-4
2-4 Appendixes
Maintenance parts list.............................................................................................................................2-4-1
General wiring diagram...........................................................................................................................2-4-2

Kyocera FS-9130DN Specifications

General

Processor model	PowerPC 750FL
Built-in processor	Yes
Maximum internal memory	576 MB
Sound power level (standby)	37 dB
Sound pressure level (printing)	56 dB
Color	No
Print technology	Laser
Maximum resolution	1800 x 600 DPI
Time to first page (black, normal)	3.5 s
Print speed (black, normal quality, A3)	23 ppm
Print speed (black, normal quality, A4/US Letter)	40 ppm
PCL fonts	80
Printer fonts	Bitmap, PCL, PostScript
Maximum duty cycle	200000 pages per month
Number of PostScript fonts	136
Number of print cartridges	1
Total input capacity	1000 sheets
Total output capacity	500 sheets
Maximum input capacity	4200 sheets
Paper tray 2 input capacity	200 sheets
Custom media sizes	(88x148 mm) - (297x450 mm)
Power requirements	AC 220 - 240V, 50/60 Hz
Networking features	Fast Ethernet 10/100Base-TX
Standard input trays	2
Media weight (tray 2)	45-200 g/m2
Maximum print size	297 x 420 mm
Duplex media weight	60 - 80 g/m²
Media weight (tray 1)	60-105 g/m2
Paper tray media types	Plain paper
ISO A-series sizes (A0...A9)	A3, A4
ISO B-series sizes (B0...B9)	B4, B5
Maximum ISO A-series paper size	A3
Mobile printing technologies	Not supported
Power consumption (standby)	160 W
Power consumption (printing)	710 W
Power consumption (PowerSave)	4.5 W
Certification	TÜV/GS, CE, PTS
Product color	Beige, Black
Standard interfaces	Ethernet, USB 2.0
Sustainability certificates	ENERGY STAR

Weight and Dimensions

Depth	646 mm
Width	599 mm
Height	615 mm