How to correct the hour on my La Crosse Technology WS-8117U-IT Alarm Clock if the minutes and date are correct?
If the hour is incorrect on your La Crosse Technology Alarm Clock, but the minutes and date are correct, ensure that you have selected the correct time zone and daylight saving time settings.
What to do if my La Crosse Technology WS-8117U-IT Alarm Clock isn't receiving the WWVB signal?
If your La Crosse Technology Alarm Clock isn't receiving the WWVB signal, try these steps: * Point the front of the clock towards Ft. Collins, Colorado, to improve reception. * Allow the clock to search for the signal overnight. * Ensure the clock is at least 6 feet away from electronic devices like TVs, computers, or other radio-controlled clocks. * Remove the batteries for 5 minutes, reinsert them, and let the unit sit overnight without pressing any buttons.
Why does my La Crosse Technology WS-8117U-IT display '--.-' in the outdoor temperature section?
If you see "--.-" in the outdoor temperature section of your La Crosse Technology Alarm Clock's LCD, try the following: 1. Remove the batteries from both the clock and the sensor for one minute, then reinsert them. Ensure you're using fresh batteries. 2. Move the clock and sensor closer to each other to ensure they are within a receivable range. 3. Relocate the units to avoid interference from other devices operating on the same frequency (915MHz).
What does 'OF.L' mean on my La Crosse Technology WS-8117U-IT outdoor temperature display?
If "OF.L" is displayed in the outdoor temperature section of your La Crosse Technology Alarm Clock's LCD, wait for the surrounding temperature to cool down or increase, as the current temperature is outside the sensor's measuring range.
What to do if my La Crosse Technology WS-8117U-IT Alarm Clock displays 'OF.L' in the indoor temperature section?
If "OF.L" appears in the indoor temperature section of the LCD on your La Crosse Technology Alarm Clock, move the clock to an area with a warmer or cooler surrounding temperature, as the current temperature is outside the measuring range.
How to fix a faint LCD display on my La Crosse Technology Alarm Clock?
If the LCD on your La Crosse Technology Alarm Clock is faint, replace the batteries.
What to do if "--.-" appears in the outdoor temperature section of La Crosse Technology Alarm Clock?
If you see "--.-" in the outdoor temperature section, it could be due to interference from other electrical devices operating on the same frequency. Try removing the batteries from both the clock and the sensor for one minute, then reinsert them, ensuring they are new. Also, the atomic clock might be out of the sensor's receivable range. Try moving the atomic clock closer to the sensor, or vice versa. As an alternative, relocate both units.
Why is my La Crosse Technology WS-8117U-IT not receiving the WWVB signal?
If your La Crosse Technology Alarm Clock isn't receiving the WWVB signal, try these steps: * Face the front of the clock towards Ft. Collins, Colorado. * Allow the clock to try and receive the signal overnight. * Ensure the clock is at least 6 feet away from electronic devices like TVs or computers. * Remove the batteries for five minutes, reinsert them, and leave the unit alone overnight without pressing any buttons.
What does "OF.L" mean on my La Crosse Technology WS-8117U-IT's outdoor temperature display and how to fix it?
If "OF.L" appears in the outdoor temperature section of your La Crosse Technology Alarm Clock's LCD, it indicates that the current temperature is outside the sensor's measuring range. You should wait until the surrounding temperature cools down or increases to come within the sensor's operational limits.
What does "OF.L" mean on my La Crosse Technology WS-8117U-IT Alarm Clock's indoor temperature display?
If "OF.L" is displayed in the indoor temperature section of your La Crosse Technology Alarm Clock's LCD, it means the surrounding temperature is outside the clock's measuring range. Move the clock to a location with a more suitable temperature.
Instructions for sensor battery installation, initial clock setup, and key functions.
Configure time zone, DST, language, and set time, date, year, month, day, weekday.
Select time display format (12/24h) and temperature units (°C/°F).
Setting the alarm, activating snooze, and deactivating the alarm.
Troubleshooting the reception of outdoor temperature signals via 915MHz.
How to cycle through different display formats for time and date elements.
How the atomic clock synchronizes with the NIST WWVB radio signal.
Guidance on optimal placement of the atomic clock and outdoor sensor.
Instructions for mounting the clock and sensor using screws or adhesive tape.
Solutions for faint displays, no WWVB signal, and outdoor signal reception errors.
Troubleshooting incorrect time settings and inaccurate temperature readings.
Guidelines for unit care, cleaning, and technical specifications.
Details on the 1-year limited warranty, coverage, and service procedures.
General| Category | Alarm Clock |
|---|---|
| Model | WS-8117U-IT |
| Brand | La Crosse Technology |
| Display Type | LCD |
| Time Format | 12/24 hour |
| Alarm Function | Yes |
| Temperature Display | Yes |
| Indoor Temperature Range | 32°F to 122°F (0°C to 50°C) |
| Weight | 0.5 lbs |
| Atomic Time | Yes |
| Alarm Features | Snooze |
| Power Source | Battery |
| Temperature Units | Fahrenheit, Celsius |
To Next Page
