lancer DELTA - User Manual

INSTRUCTIONS FOR TROUBLE SHOOTING
LANCER ELECTRONIC ICE BANK CONTROL (EIBC)
FOR MODELS: DELTA/1500/800
1. To check for normal PCB operation, please refer to the following instructions.
1.1 Turn power OFF or ensure that power has been disconnected from dispenser.
1.2 Pull PCB upward, so that it is no longer connected to the terminal block.
W
ARNING
TERMINAL BLOCK HAS AC LINE VOLTAGE AND SHOULD BE COVERED WITH TAPE.
INSERT A SMALL STRIP OF ELECTRICAL TAPE BETWEEN BOARD AND CONNECTOR TO
PREVENT RE-CONNECTION.
TAPE SHOULD COVER BARE ELECTRICAL CONNECTIONS TO PREVENT ELECTRICAL
SHOCK.
1.3 Disconnect both the Ice Bank probe (J2) and the Carbonator probe (J3) (if equipped) connections
from board (see Figure 1 on reverse).
1.4 Use a short copper wire, paper clip, or other means to short the Ice Bank probe terminals (J2) on
the PCB by touching all three (3) pins together.
1.5 Set Ohm test meter to measure continuity.
1.6 Reconnect power or turn dispenser ON. Observe time and check continuity of the PCB edge
connector (see Figure 1 on reverse).
A. The following should be observed:
1. Terminal 3 to 2 (Carbonator): During the first 2.5 to 3.5 minutes, there should be continuity.
After 2.5 to 3.5 minutes, there should be NO continuity.
2. Terminal 3 to 1 (Compressor): During the first 4 to 6 minutes, there should be NO continu-
ity. After 4 to 6 minutes, there should be continuity. Remove wire from J2 connector. There
should be NO continuity from 3 to 1.
3. You should be able to hear the “click” sound of the relay closing when the time delays end.
1.7 Turn electrical power OFF for 15 seconds and then back ON again to reset Carbonator timer. Again,
measure continuity of the PCB edge connector.
A. Terminal 3 to 2: There should be continuity. Use a short copper wire, paper clip, or other means
to short the Carbonator probe terminals (J3) on the PCB by touching all three (3) pins together.
This should be done before the 2.5 to 3.5 minute time limit has elapsed. Measure the
continuity again between Terminal 3 to 2. There should be NO continuity.
1.8 If all the above work as noted, then the board is functioning properly. Remove tape and reconnect
board. If any non-conformities are found, the PCB must be replaced (PN 52-0952/01).
DATE: 03/18/98
P.N.: 28-0393
6655 LANCER BLVD. • SAN ANTONIO, TEXAS 78219 USA • (210) 310-7000
FAX SALES
• USA -CANADA – 210-310-7250 • LATIN AMERICA – 210-310-7245 • ASIA – 210-310-7242 •
• EUROPE – 32-2-755-2399 • PACIFIC – 61-8-8268-1978 •
FAX ENGINEERING: • 210-310-7096
"Lancer" is the registered trademark of Lancer • Copyright — 1998 by Lancer, all rights reserved.

Summary

PCB Operation Check and Troubleshooting

Power Down and PCB Disconnection

Turn power OFF, disconnect dispenser, pull PCB upward, and secure terminal block with tape to prevent shock.

Disconnecting Probes

Disconnect Ice Bank (J2) and Carbonator (J3) probes from the board.

Ice Bank Probe Continuity Test

Short Ice Bank probe terminals (J2) and measure continuity with an Ohm meter.

Initial Continuity Observation

Reconnect power, observe continuity for J2 (3-2) and J2 (3-1), and listen for relay clicks.

Carbonator Timer Reset and Test

Turn power OFF/ON to reset Carbonator timer. Short Carbonator probe terminals (J3) and measure continuity for J3 (3-2).

Functionality Confirmation

If all tests pass, the board is functional. Remove tape, reconnect, or replace PCB if non-conformities are found.

lancer DELTA Specifications

General

Frequency	50/60 Hz
Protection	Overload
Communication	Modbus RTU
Enclosure	NEMA 4X
Voltage Rating	208-600 VAC