Why does water continually overflow from the water bath into the drip tray in my Lancer Dispenser?
To address water continually overflowing from the water bath into the drip tray of your Lancer Dispenser: 1. Tighten any loose water connections. 2. Replace the flare seal washer if it's leaking. 3. Replace the water coil if it's faulty.
Why does the BIB pump fails to restart when dispensing valve is closed on my Lancer Dispenser?
If the BIB pump fails to restart when the dispensing valve is closed on your Lancer Dispenser: 1. Repair or replace the discharge line or fittings if there's a leak. 2. Replace the BIB if it's empty. 3. Repair or replace the inlet line or bag connector if there's an air leak.
What to do if the BIB pump fails to restart after bag replacement in my Lancer Dispenser?
If the BIB pump fails to restart after bag replacement in your Lancer Dispenser: 1. Tighten the BIB connector. 2. Clean out or replace the BIB connector if it's stopped up. 3. Straighten or replace the syrup line if there are kinks. 4. Replace the BIB pump if necessary.
Why does the BIB pump continue to operate when the bag is empty in my Lancer Dispenser?
If your Lancer Dispenser's BIB pump continues to operate when the bag is empty: 1. Replace the suction line if there is a leak. 2. Replace the o-ring on the pump inlet fitting if it's leaking.
What to do if BIB pump operated, but no flow from my Lancer Dispenser?
If the BIB pump operated, but there is no syrup flow in your Lancer Dispenser: 1. Replace the syrup inlet or outlet line if there is a leak. 2. Replace the BIB pump if the check valve is defective.
Why is there insufficient water flow in my Lancer Dispenser?
To address insufficient water flow in your Lancer Dispenser: 1. Verify the incoming supply water pressure is a minimum of 25 Psi (0.172 MPa). 2. Fully open the shutoff on the mounting block. 3. Remove any foreign material from the water flow control. 4. Clean the water pump strainer.
What causes miscellaneous leakage in my Lancer Dispenser?
To resolve miscellaneous leakage in your Lancer Dispenser: 1. Tighten the appropriate retaining screws. 2. Replace or adjust the appropriate o-rings.
How to fix water leakage around the nozzle of my Lancer Dispenser?
To fix water leakage around the nozzle of your Lancer Dispenser: 1. Install or replace the o-ring correctly above the diffuser. 2. Replace the o-ring if it is damaged or missing.
What to do if the valve will not shut off on my Lancer Dispenser?
If your Lancer Dispenser valve won't shut off, check these: 1. See if the cup lever is sticking or binding; correct or replace the lever. 2. Check the switch for free actuation. 3. Replace the defective armature or spring if the solenoid armature isn't returning to the bottom position.
Why is there insufficient syrup flow in my Lancer Dispenser?
To address insufficient syrup flow in your Lancer Dispenser: * Ensure the CO pressure to the BIB pumps is adjusted to 80 Psi (0.550 MPa), with a minimum of 70 Psi (0.480 MPa). * Replace or refill the CO tank. * Fully open the shutoff on the mounting block. * Remove any foreign material from the syrup flow control. * If needed, replace the BIB pump.
Warnings and precautions regarding the flammable refrigerant used in the unit.
Hazards and precautions associated with carbon dioxide gas.
Critical warnings for electrical connections and maintenance.
Detailed instructions for physically installing the dispenser unit.
Procedure for connecting and setting up the carbon dioxide gas supply.
A guide to identify and resolve common dispenser issues.
Specific troubleshooting for post-mix dispensing issues.
Schematic showing the electrical connections and layout of the unit.
Schematic illustrating the water and CO₂ flow paths within the unit.
To Next Page
General