Land Pride Rotary Cutters RCR1860 User Manual (English)

Questions and Answers:

D
David JohnsonAug 19, 2025
What to do if the driveline clutch is slipping on my Land Pride Rotary Cutters RCR1860?
- B
  bradleyknappAug 19, 2025
  If the driveline clutch on your Land Pride Lawn Mower is slipping, it could be due to several reasons. You might be scalping the ground, so try raising the cutting height. Another cause could be cutting too fast, in which case you should reduce your travel speed. Also, engaging the PTO too fast at high engine RPMs can cause slippage, so slowly engage the PTO at low engine RPMs. Finally, avoid cutting over solid objects.
K
Kelly LynchAug 21, 2025
Why is there excessive vibration in my Land Pride Rotary Cutters RCR1860?
- R
  Rachel CraigAug 21, 2025
  If you notice excessive vibration in your Land Pride Lawn Mower, several issues could be the cause. A bent driveline, loose blades, a bent blade carrier, or a broken blade could all contribute to this problem. Replace these parts if needed. Also, check if a blade will not swing and remove it for inspection. Unequal blade weight can also cause vibration, so replace both blades.
C
crystal13Aug 25, 2025
Why are the blades wearing excessively on my Land Pride Rotary Cutters RCR1860?
- D
  Dean GordonAug 25, 2025
  Blades on your Land Pride Lawn Mower might be wearing excessively because you are cutting on sandy ground or frequently contacting the ground. To solve this, raise the cutting height.
M
michelle58Aug 26, 2025
Why are the blades breaking on my Land Pride Lawn Mower?
- P
  Paul OliverAug 26, 2025
  If the blades are breaking on your Land Pride Lawn Mower, it's likely due to hitting solid objects. Make sure to avoid hitting solid objects while mowing.
R
rwilliamsAug 28, 2025
Why does the blade carrier become loose on my Land Pride Rotary Cutters RCR1860 Lawn Mower?
- R
  Ryan AllisonAug 28, 2025
  If the blade carrier on your Land Pride Lawn Mower becomes loose, it could be due to running loose in the past. If this is the case, replace the gearbox output shaft and blade carrier. Alternatively, the blade carrier hardware might not be tight enough, so tighten it to the specified torque.
L
Lisa CooperAug 29, 2025
Why are the blades coming loose on my Land Pride Rotary Cutters RCR1860?
- K
  Katie AllenAug 29, 2025
  If the blades are coming loose on your Land Pride Lawn Mower, it could be because the blades were not tightened properly. Make sure to tighten the blade hardware. Improper deck attitude can also cause this issue, so lower the front of the deck.
J
Jennifer LoganAug 31, 2025
What causes a bent blade carrier on a Land Pride Lawn Mower?
- T
  Tammy SmithAug 31, 2025
  If the blade carrier is bent on your Land Pride Lawn Mower, it's likely due to hitting solid objects. Avoid hitting solid objects and replace the blade carrier.
J
John RodriguezSep 3, 2025
What causes the driveline yoke or cross to fail on a Land Pride Rotary Cutters RCR1860?
- M
  Mark BurkeSep 3, 2025
  If you notice the driveline yoke or cross failing on your Land Pride Lawn Mower, it could be due to a shock load. Avoid hitting solid objects. It may also be due to lack of lubrication, so lubricate every 8 hours.
H
Hayden BauerSep 4, 2025
What causes driveline telescoping tube failing on Land Pride Rotary Cutters RCR1860 Lawn Mower?
- T
  Timothy AllenSep 5, 2025
  If the driveline telescoping tube is failing on your Land Pride Lawn Mower, it is probably due to shock load. Avoid hitting solid objects.
G
Gregory WhiteSep 6, 2025
What causes driveline telescoping tube wearing on Land Pride Rotary Cutters RCR1860 Lawn Mower?
- J
  Jonathan PayneSep 6, 2025
  If the driveline telescoping tube on your Land Pride Lawn Mower is wearing, it needs lubrication. Make sure to lubricate it every 20 hours.

Land Pride Rotary Cutters RCR1860 Specifications

General

Cutting Width	60 inches
Hitch Type	Category 1
Gearbox HP Rating	40 hp
PTO Speed	540 RPM
Horsepower Requirements	20-40 hp
Gearbox Rating	40 HP
Blade Carrier	Round Pan
Driveline Protection	Shear Bolt
Number of Blades	2
Required PTO HP	20 HP
Cutting Height Range	1.5 - 9 inches