Larsen & Brusgaard Viso II User Manual

30
31
same body position), whereas TAS will show a different speed throughout the dive
(the same body position, different air density).
Below are some recommendations and numbers for SAS:
A good base speed should be: 110-115 mph.
A high base speed should be: 120-125 mph (tendency to wobble when docking).
A slow base speed should be: 100-105 mph (jumpers start to go low).
See separate section on page 61 for more information about TAS and SAS.
VISO II Settings
True Airspeed (TAS) / Skydiver’s Airspeed (SAS)
VISO II Settings
Press or to toggle between TAS and SAS.
The active selection flashes.
Press to save setting and enter the Set Current Year
selector.
NOTE: Jump data is continuously stored in both TAS and SAS.
Stored information may be displayed in either unit of measure-
ment by selecting the respective mode.
Recommendation:
When using the VISO II as a Speed-Meter in a big way base it
is recommended to set it to SAS.
SAS will show the same speed throughout the dive (at the
32
33
Set Current Date Selector
Alti-Meter/ Speed-Meter • Feet/ Meter when set to Alt i-Meter • Mph/ Kmh when set to Speed-Meter • Alt itude
offset • Dive Type • True Airspeed (TAS)/ Skydiver’s Airspeed (SAS) • Set current year • Set current date • Set
current time • Preset jump counter • Reset jump counter • Turn the VISOII OFF• Padlock window
VISO II Settings
Set Current Date
Press to increase date.
Press to decrease date.
Press to save setting and enter the Set Current Time selec-
tor.
Note: Date format is MM:DD.
Set Current Year Selector
Alti-Meter/ Speed-Meter • Feet/ Meter when set to Alt i-Meter • Mph/ Kmh when set to Speed-Meter • Alt itude
offset • Dive Type • True Airspeed (TAS)/ Skydiver’s Airspeed (SAS) • Set current year • Set current date • Set
current time • Preset jump counter • Reset jump counter • Turn the VISOII OFF• Padlock window
VISO II Settings
Set Current Year
Press to increase year.
Press to decrease year.
Press to save setting and enter the Set Current Date selec-
tor.
34
35
Preset Jump Counter Selector
Alti-Meter/ Speed-Meter • Feet/ Meter when set to Alt i-Meter • Mph/ Kmh when set to Speed-Meter • Alt itude
offset • Dive Type • True Airspeed (TAS)/ Skydiver’s Airspeed (SAS) • Set current year • Set current date • Set
current time • Preset jump counter • Reset jump counter • Turn t he VISOI I OFF • Padlock window
Explanation
The VISO II can store up to 200 jumps in the logbook and numbers them starting
from the jump number that you preset here. The counter can be used to keep track
on the number of jumps and it can be reset at any time, but time and date for the
last reset remains stored and cannot be erased.
VISO II Settings
Preset Jump Counter
Press to increase the jump counter.
Press to decrease the jump counter.
Press to save setting and enter the Reset Jump Counter
selector.
Set Current Time Selector
Alti-Meter/ Speed-Meter • Feet/ Meter when set to Alt i-Meter • Mph/ Kmh when set to Speed-Meter • Alt itude
offset • Dive Type • True Airspeed (TAS)/ Skydiver’s Airspeed (SAS) • Set current year • Set current date • Set
current time • Preset jump counter • Reset jump counter • Turn the VISOI I OFF• Padlock window
VISO II Settings
Set Current Time
Press to increase time.
Press to decrease time.
Press to save setting and enter the Preset Jump Counter selec-
tor.
Note: Time format is HH:MM and in 24-hour format

Larsen & Brusgaard Viso II Specifications

General

Brand	Larsen & Brusgaard
Model	Viso II
Category	Measuring Instruments
Language	English