Lauda IN 1590 XTW User Manual

Integral Process Thermostats and High-Temperature Thermostats
Operation manual
IN 130 T, IN 230 T, IN 230 TW, IN 530 T, IN 530 TW, IN 1030 T, IN 1330 TW, IN 1830 TW, IN 150 XT,
IN 250 XTW, IN 280 XT, IN 280 XTW, IN 550 XT, IN 550 XTW, IN 590 XTW, IN 750 XT, IN 950 XTW, IN 1590 XTW,
IN 1850 XTW, IN 2560 XTW, IN 2050 PW, IN 2560 PW, IN 4 XTW, IN 8 XTW
V6R9
Read this manual prior to performing any task!

Lauda IN 1590 XTW Specifications

General

Temperature stability	±0.01 °C
Cooling power at 20°C	800 W
Cooling Power	0.6 kW at 20°C
Power Supply	400 V, 50/60 Hz
Working temperature range	-40°C to 200°C
Temperature Range	-40°C to 200°C

Summary

Safety

Safety information

Important safety information, device operation conditions, and warnings.

Obligations of the operator

Operator's responsibilities regarding system installation and statutory regulations.

Prohibition of modifications to the device

Prohibits user modifications and outlines warranty implications.

Requirements for the heat transfer liquid

Personnel qualification

Personal protective equipment

Details necessary personal protective equipment (gloves, clothing, glasses).

Safety fittings on the device

Describes overtemperature and low-level protection systems and product safety labels.

Device description

Hydraulic circuit

Before starting up

Install device

Instructions and warnings for installing the device, including handling and surface requirements.

Hoses

Connecting an external application

Instructions and warnings for connecting the device to an external application.

LAUDA heat transfer liquids

Information on LAUDA heat transfer liquids, including recommendations and safety data.

Cooling water requirements

Configuring interfaces

Commissioning

Establishing a mains connection

Instructions and warnings for connecting the device to the power supply.

Switching on the device for the first time

Step-by-step guide for initial device power-on and language selection.

Operating the device with the operating unit

Description of the home window, navigation keys, softkeys, and parameter entry.

Setting heat transfer liquid

Instructions and warnings for setting the heat transfer liquid and overtemperature protection.

Fill the device with heat transfer liquid

Procedure and warnings for filling the device with heat transfer liquid.

Degas heat transfer liquid (low boiling point expulsion)

Procedure for degassing heat transfer liquid to remove low boilers and prevent issues.

Setting the flow rate of the heat transfer liquid

Control parameters

Information on adjusting control parameters for optimal temperature control.

Operation

General warning

General safety warnings related to heat transfer liquid, splashing, and overheating.

Operating modes

Setting Tmax

Instructions for setting the maximum temperature limit (Tmax) for safety.

Self adaptation

Set the setpoint offset

Limiting heating and cooling

Dead-time correction

Dynamic heatlimiter

Setting temperature limits Tih and Til

Basic settings

Calibrating the temperature probe

Procedure for calibrating the temperature probe for accurate measurements.

Restore the factory setting

Through-flow control of the internal heater

Programmer

Functions for creating, editing, and executing temperature-time programs.

Operator and viewer

Web server LAUDA Command

Cloud service LAUDA.LIVE

Safe Mode safety fittings

Configuring an emergency operating mode for device and application safety during process faults.

Operation of a high-temperature thermostat

Operating a device with pressure overlay

Warnings, safety instructions and further information

Warnings and safety instructions specific to devices with pressure overlay functionality.

The system pressure in devices with pressure overlay

Setting the parameters for a pressure-stable application up to the maximum system pressure

Setting the parameters for a pressure-stable application

Filling and operating a device with pressure overlay

Procedure for filling the device and operating it with pressure overlay.

Maintenance

Warning notes for maintenance

General safety warnings and protective equipment required before performing maintenance.

Maintenance intervals

Table detailing routine maintenance tasks and their recommended intervals.

Checking the overtemperature protection

Procedure to verify the functionality of the overtemperature protection system.

Checking the low-level protection

Procedure to verify the functionality of the low-level protection system.

Check the heat transfer liquid

Procedure for checking the usability and condition of the heat transfer liquid.

Faults

Alarms, errors and warnings

How alarms, errors, and warnings are displayed and handled on the device.

Alarms

List of constant temperature equipment alarms, their messages, descriptions, and user actions.

Troubleshooting

Guide to diagnosing and resolving common faults and issues with the process thermostat.

General

Contact LAUDA

Contact information for LAUDA Service for troubleshooting and technical questions.

Technical data

Heating output and power supply

Cooling output

Refrigerant and filling weight

Technical data of the high-temperature thermostats

Pump characteristics for Integral T

Pump characteristics for Integral XT

Pump characteristics for high-temperature thermostats