Lauda IN 2560 XTW - User Manual

Integral Process Thermostats and High-Temperature Thermostats
Operation manual
IN 130 T, IN 230 T, IN 230 TW, IN 530 T, IN 530 TW, IN 1030 T, IN 1330 TW, IN 1830 TW, IN 150 XT,
IN 250 XTW, IN 280 XT, IN 280 XTW, IN 550 XT, IN 550 XTW, IN 590 XTW, IN 750 XT, IN 950 XTW, IN 1590 XTW,
IN 1850 XTW, IN 2560 XTW, IN 2050 PW, IN 2560 PW, IN 4 XTW, IN 8 XTW
V6R9
Read this manual prior to performing any task!

Summary

1 Safety

1.1 Safety Information

General safety information, warnings, and safe state definitions for device operation.

1.2 Operator Obligations

Operator responsibilities, regulatory compliance, and requirements for system installation.

1.15 Safety Fittings

Details overtemperature protection and low-level protection safety units on the device.

2 Unpacking

2 Unpacking Procedures

Instructions for unpacking the device, checking for completeness, and handling transport damage.

3 Device Description

3.4 Integral Large casing with pressure overlay

Visual overview of large casing Integral devices with pressure overlay features.

3.7 Hydraulic Circuit

Explanation of the hydraulic circuit in Integral T and Integral XT devices.

3.8 Rating Label

Details on the LAUDA device rating label specifications and their meaning.

3.9 Interfaces

Overview of standard and accessory interface modules for device connectivity.

4 Before Starting Up

4.1 Install Device

Guidelines for correct device installation, handling, and environmental conditions.

4.3 Connecting an External Application

Instructions for connecting external applications, including safety warnings.

4.4 LAUDA Heat Transfer Liquids

Information on permissible heat transfer liquids, their properties, and handling guidelines.

4.5 Cooling Water Requirements

4.7 Configuring Interfaces

5 Commissioning

5.1 Establishing a Mains Connection

Procedure for connecting the device to the mains power supply.

5.2 Initial Device Startup

5.3 Operating the Device with Operating Unit

Guide to operating the device using the control unit, including navigation and windows.

5.4 Setting Heat Transfer Liquid

Instructions for selecting and setting the heat transfer liquid used in the device.

5.5 Filling the Device

Procedure for filling the device with heat transfer liquid, including safety warnings.

5.6 Degassing Heat Transfer Liquid

Steps for degassing the heat transfer liquid using the low boiling point expulsion method.

5.7 Setting Flow Rate

5.8 Control Parameters

6 Operation

6.1 General Warning

General safety warnings for device operation, including hazards related to heat transfer liquid.

6.4 Setting Tmax

6.5 Self Adaptation

6.14 Calibrating the Temperature Probe

6.18 Programmer

6.21 Web Server LAUDA Command

6.22 Cloud Service LAUDA.LIVE

6.23 Safe Mode Safety Fittings

Configuration and activation of Safe Mode for emergency device operation.

6.24 Importing and Exporting Data

8 Operating a Device with Pressure Overlay

8.1 Warnings and Safety Instructions

Safety guidelines and warnings specific to devices with pressure overlay.

8.4 Setting Parameters for Pressure-Stable Application

8.6 Filling and Operating with Pressure Overlay

9 Maintenance

9.1 Warning Notes for Maintenance

Safety precautions and protective equipment required before performing maintenance.

9.2 Maintenance Intervals

9.6 Checking Overtemperature Protection

9.7 Checking Low-Level Protection

10 Faults

10.1 Alarms, Errors, and Warnings

Explanation of how alarms, errors, and warnings are displayed and handled.

10.2 Alarms

10.3 Troubleshooting

Table of common faults, their causes, and possible remedies for process thermostats.

Lauda IN 2560 XTW Specifications